Shipboard Emergency Drills must be carried out at least (OPA-90):
In a refrigeration system what is the most likely cause of the compressor suction pressure being too law and causing the compressor to short cycle?
System overcharged with refrigerant.
Insufficient cooling water flow through the condenser.
Expansion valve stuck open.
System undercharged with refrigerant.
What would be the most probable cause of the exhaust gas temperature from one cylinder of a diesel engine being lower than normal?
The opening pressure for the injection valve for the cylinder is set too high.
There is air in the fuel oil system.
The camshaft chain is too slack.
The intake filter for turbo charger is partly fouled.
Which of the methods given in the options should be used to test a remote reading temperature gauge for the auxiliary boiler exhaust gas?
Check the resistance change in the sensor over a known temperature range against the resistance values in the product sheet.
Fit a spare temperature gauge and see if the reading are the same.
Place the sensor in a test tank of water fitted with a heater element and thermometer and check the temperature gauge at different temperatures.
Place the sensor in a test tank of oil fitted with a heater element and thermometer and check the temperature gauge at different temperatures.
Which one of the listed requirements regarding the stowage of a survival craft corresponds to present SOLAS regulations? Each survival craft shall be stowed:
In a secure and sheltered position and protected from damage by fire or explosion.
Wherever space is available.
In a state of readiness so that two crew-members can prepare for embarkation and launching in less than 15 minutes.
On the starboard side of the ship.
During inspection of a high pressure fuel pump for a medium speed diesel engine it is observed that the upper leading edge and the lower helical edge of the pump plunger have suffered from erosion damage. Select the correct action to take to remedy this from the options given.
Renew only the plunger if the barrel appears undamaged.
Renew the plunger and barrel insert as a pair.
Smooth away the damaged area with a grinder and polishing stone and refit it.
Replace the complete pump with a new or reconditioned spare.
What is the first thing that should be checked when taking over a boiler watch?
The boiler room bilge level.
The oil pressure to the burner.
The boiler exhaust gas colour.
The examples of Aromatic Hydrocarbons will include:
Benzene, Toluene and Xylene.
Hydrogen Sulphide and Carbon Monoxide.
Carbon Dioxide and Hydrogen Peroxide.
Propane, Butane and Pentane.
What is the correct understanding of the term “Lapse Rate” when used in Meteorology?
The rate of increase of the wind associated with a Tropical Revolving Storm.
The delay in temperature reduction associated with the wet bulb thermometer of a hygrometer.
The change in the temperature associated with the passing of the warm front of a frontal depression.
The change of the temperature in the atmosphere with height above sea level.
Water is the extinguishing agent which is the most widely employed and its action as an extinguishing agent is due to a combination of the following phenomena:
Smothering and inhibition.
Cooling, smothering and dispersion.
Smothering and dispersion.
Cooling, inhibition and dispersion.
A small electric motor needs to be taken to the bottom plates for fitting to a domestic water pump. It is only just too heavy to be manually carried so is to be lowered using the engine room crane. Which of the options given would be a suitable strop to use for the operation?
Any certified strop which has a safe working load greater than the weight of the motor.
A wire strop which is rated for twice the required load but is out of certification.
Any piece of rope will do as the motor is only just too heavy to carry.
Any strop which looks big enough to carry the load.
High Voltage (HV) cables are smaller than low voltage cables for a given power rating. Why is this?
The HV cable carries a smaller current and therefore requires less copper.
The HV cable uses higher quality copper conductors and therefore requires them to be a smaller cross-sectional area.
The HV cable uses Aluminium conductors and therefore requires them to be a smaller cross-sectional area.
The HV cable has a thinner wall of special insulation material.
After checked for open airway, given the first two inflations and checked the pulse to make sure that the heart is beating, what is the rate of inflations given until natural breathing is restored?
Doesn’t matter how many times.
The normal carbon content of Crude Oil is in the range of:
An alarm signal consisting of seven short blast followed by one prolonged blast is sounded by the ship’s whistle and alarm bells. What are you to do?
Go to your lifeboat station.
Go to (or remain in) your cabin and await further orders.
Report on the bridge (deck crew) or engine room (engine crew) for further orders.
Which of the options given is the main reason for using a ring spanner to tighten the brass nuts on the cover studs of a pump casing?
It can be adjusted to the exact size of the nut.
It will allow the nuts to be tightened correctly.
The nuts can be tightened more with this type of spanner.
It will minimise the risk of slipping off the nut or damaging the nuts.
What are the lists called that give the position and task during a lifeboat drill for all persons on board the ship?
The engine room rating has been assisting with ballast operations during a period of engine room watch duty. Ballast operations have stopped for a couple of hours while stores are being taken. What action should the rating take during this break in operations?
Just keep the pumps running and the valves for the ballast tanks open to save time when operations are restarted. The tanks will just overflow through the air vents.
Just stop the pumps and close the pump suction and discharge valves. Leave the valves for the ballast tanks open to save time later.
Shut the valves for the ballast tanks but keep the pumps running and discharging overboard to save time later.
Stop all of the ballast pumps and close all of the ballast valves as soon as operations are stopped. Ballast lines should always be closed except when they are being used.
An electric motor is to be aligned to a pump by insuring shims under the motor feet. Which of the tools given in the options would be used to check that the alignment is correct by measurement of the gap between the coupling faces?
An inside vernier calliper.
Give the meaning of the following symbol:
Remote controlled fire pumps.
International shore connection.
What would you do if you are told to operate a piece of mechanical equipment which you are not familiar with?
Seek advice from your superior before attempting to operate it.
Ensure that all safety guards and devices are disconnected.
Try and guess how the equipment should be operated.
Ignore the request to operate the equipment.
An important quantity which is useful in circuit analysis is known as conductance G (Siemens). Which of the formulas A to D expresses the conductance for this circuit?
What types of fire extinguishers shall be used in the engine room?
Fire extinguishers of the handy-size types only.
Fire extinguishers filled with fresh water only.
Fire extinguishers equipped for powder or CO2 only.
Any fire extinguisher with a weight of less than 100 lbs.
The insulation resistance (IR) to earth of a new galley hot-plate is measured to be 30 Mohm. When three identical hot-plates on the same supply are tested together their combined IR will be:
An electric motor is to be aligned to a pump by insuring shims under the motor feet. Which of the tools given in the options would be used to check that the alignment is correct by measurement of the gap between the coupling faces?
An inside vernier calliper.
The small amounts of cargo found in the cargo tanks before loading is referred to as OBQ, which means:
OPB (Observed Preliminary Volume).
TSV (Total Surveyed Volume).
ROB (Remaining On Board).
As per international regulations, the minimum inert gas pressure required to be maintained in slop tanks if slops are retained on board is:
When operating a propulsion installation consisting of medium speed diesel engines driving a controllable pitch propeller it is possible to operate the combination of engine speed and propeller pitch in a number of different ways. What would be the main reason for operating with constant speed and variable pitch?
To allow the engine to be operated with a load sensing governor instead of a speed sensing governor.
To allow rapid load change and thrust reversal when manoeuvring.
To obtain maximum propeller efficiency over the load range of the engine.
To allow constant speed operation of a shaft generator while the engine load changes with pitch variation.
What is generally considered as the minimum safe time period before opening a crankcase door after the oil mist detector alarm has activated and the engine has been stopped?
After at least 20 minutes.
After at least 10 minutes.
After at least 5 minutes.
Why should boiler sootblowers normally only be operated in the correct sequence?
To ensure soot is cleared progressively from the bottom tubes to the top and toward the boiler uptakes.
To minimise loss of steam pressure.
So that the operator does not forget which sootblowers have been used.
To avoid excess stress in the boiler.
An engine room rating is assisting in the maintenance of some of the valves on the low pressure steam range. Which packing material, from the options given, would be the best choice for repacking the gland of a low pressure steam valve?
Lead covered cotton packing.
What is the “International shore connection” used for?
To connect the ship fire main to the shore lines.
To connect the cargo hoses to the shore.
To connect the bunker hoses to the shore.
To connect the ship fresh water hoses to the shore.
What would be the effects of a ship passing into shallow waters?
The vessel has a tendency to swing to port with a single fixed-pitch right-hand turning propeller.
The speed is not affected, but more rudder is required to steer the ship.
There is no noticeable difference in performance of the ship.
The ship is less responsive to both rudder and propeller.
What is the main difference between a stuffing box gland and a mechanical seal on a centrifugal pump?
If packing fails the pump can be kept running by tightening the glands, but if a mechanical seal fails it must be renewed to stop the leakage.
The sealing surface of a mechanical seal is usually parallel to the shaft, but sealing surface of a packed gland is perpendicular to the shaft.
Packed stuffing box glands are subject to wear but mechanical seals are not.
Packed stuffing box glands must be cooled by liquid, but mechanical seals do not require any cooling.
The purpose of having corrugations in the bulkheads of cargo tanks of an oil tanker is to:
Provide strength, but with clean and clear surfaces within the tank.
To assist in the drainage of the oil by funneling the oil to the suction well.
Reduce the effects of Free Surface within the vessel.
Provide additional resistance to shear forces and bending moments.
Is it necessary to cool the samples taken from a diesel engine cooling water system before carrying out tests to determine the concentration of treatment chemicals?
No, the samples should be heated to approximately 95 °C.
Yes, the samples should be cooled to approximately 25 °C.
Yes, the samples should be cooled to approximately 50 °C.
No, the test should be carried out at system temperature.
The ship is involved in a collision, what is the immediate action by the Officer of the Watch after the incident has taken place?
Sound the General Alarm and stop engines.
Contact the other ship and send the bridge lookout down to start taking soundings.
Call the Master and check the position for any immediate dangers.
Stop engines and check over the side for any signs of pollution.
The purpose of the demister unit within the Inert Gas System is:
To remove sulphur oxides.
To remove water from the IGS stream.
When shutting down the flue gas plant, the last step that the operator shall carry out would be to:
Close the deck isolating valve.
Open ventilation valve to atmosphere.
Close the gas pressure control valve.
Shut down of inert gas blower.
During cargo or bunker operations, oil response equipment is to be:
Used elsewhere in the ship.
You have abandoned ship in a liferaft. In most cases, which of the following actions should you generally take?
Organise a lookout system. Join up with other survival craft if possible. Stream the sea anchor.
Organise a lookout system.
Join up with any other survival craft and stream the sea anchor.
Start paddling in the direction of the nearest land.
What is the emergency channel on VHF?
Which of the following areas may be possible restricted areas? Review all answers.
What are the lists called that give the position and task during a lifeboat drill for all persons on board the ship?
Which of these are indicators that an individual may be a drug smuggler?
The individual makes small local purchases.
The individual is disinterested in the ship’s cargo.
The individual wears bulky or out of season clothing.
The individual spends his or her free time hanging out with others.
When shutting down the flue gas plant, the last step that the operator shall carry out would be to:
Shut down of inert gas blower.
Close the gas pressure control valve.
Close the deck isolating valve.
Open ventilation valve to atmosphere.
What will a cadet find in the maintenance manual?
A cadet will find a lubricating chart in the maintenance manual.
A cadet will find grease in the maintenance manual.
A cadet will find machinery spare parts in the maintenance manual.
A cadet will find grease nipples in the maintenance manual.
In carbon dioxide fire-fighting systems for use in machinery spaces the fixed piping system shall be such that:
85 % of the gas can be discharged into the space within 2 minutes.
100 % of the gas can be discharged into the space within 2 minutes.
100 % of the gas can be discharged into the space within 3 minutes.
70 % of the gas can be discharged into the space within 1 minute.
What kind of extinguishing-remedy would you choose to put out an electrical fire?
Combination of powder and water.
Dry extinguishing remedy.
With reference to the efficiency of cargo pumps on oil tankers, the abbreviation NPSH stands for:
Necessary Pumping Suction Hazard.
Natural Pumping Standard Height.
Nominal Pressure Suction Head.
Net Pressure Suction Head.
What kind of measure is the division of the vessel in upright areas by using thermic and structural separations?
It is both a prevention and protection measure.
It is a protection measure.
It is a prevention measure.
It is neither a prevention nor a protection measure.
During maintenance work in the engine room or on deck it is often necessary to work aloft (work at a height above the plates or the deck). When working aloft onboard the ship what is the most important safety precaution that should be taken?
Wear a safety harness securely attached to ship’s structure.
Wear a safety helmet and goggles.
Lash the bottom of the ladder to a fixed point.
Keep all the tools required for the work in a bucket.
What action should be taken if it is noticed that there is a quantity of oil on the engine room tank top?
Start the fire pump and wash the oil into the bilges.
Open the overboard valve and start the bilge pump.
Apply foam to the tank top to minimise any risk of fire.
Notify the duty engineer and try and find the cause of the leakage so that it can be stopped and the oil cleaned up.
What special equipment can often provide assistance in locating a survival craft or man overboard and in the water?
A sectored search pattern.
What is the most likely cause of black smoke at the boiler exhaust during normal operation of a steam boiler?
Insufficient combustion air.
Fuel oil temperature too high.
What does the word “pyrotechnics” mean?
Pyrotechnics are the items which are capable of self-contained chemical reactions for the production heat, light, smoke and/or sound.
Pyrotechnics are items that are used to produce technical solutions to the complex problems.
Pyrotechnics are used to ensure that the correct technical proportions are used to start the system functioning.
Pyrotechnics is a group word to cover all the required activities in the event of a man overboard.
Which of the following answers would most appropriately describe shell plating damage to the vessel?
My vessel has sustained damage to shell plating below the waterline.
My vessel has sustained damage to shell plating below the waterline in way of No. 3 cargo hold, starboard side.
My vessel has sustained damage to shell plating in way of No. 3 cargo hold.
My vessel has sustained damage to shell plating above the waterline.
While getting tools ready and preparing for overhaul work on the main engine the engine room rating notices that the electrical extension is damaged. A small section of the cables outer insulation is split although the inner insulation appears ok. What action should the rating take?
Cut off the end of the cable including the damaged section and refit the plug to the end of the remaining cable before using the extension.
Label the damaged extension as unfit for use and return it to the store for testing and get a replacement extension.
Carry on using the extension after wrapping insulation tape over the damaged section as it is only minor damage.
Just use the extension as it is since the damage is only to the outer insulation and the inner insulation appears ok.
For how long should the self contained air support system on a totally enclosed lifeboat having its engine running be capable of providing safe and breathable air?
An engine room rating notices that the guard on a running pump is hanging loose due to a missing bolt on the support bracket and it is catching the shaft coupling. What is the best action to take as a repair method?
Try and fit a new bolt while the pump is running to permanently fix the guard in place.
Inform the watchkeeper so that the pump can be stopped and a new bolt can be fitted to permanently fix the guard in place.
Fasten the guard back in place with a piece of rope with the pump running as a temporary repair.
Place a sheet of metal in front of the guard to deflect any parts that may fly off as a temporary repair.
What is flashpoint of an oil or liquefied gas?
The flashpoint is the mixture of oxygen and hydro carbons needed to have an oil or liquefied gas to burn.
The flashpoint for an oil or liquefied gas is the temperature at which it is possible to ignite the vapour above the liquid.
The flashpoint is the temperature the oil or liquefied gas need for self ignition.
The flashpoint is the temperature needed to have a oil or liquefied gas pumpable.
What term is used to describe a fresh water cooling system which contains a seawater cooled common freshwater cooler and which meets the cooling requirements for all the engine room machinery?
A high temperature freshwater system.
A low temperature freshwater system.
A central cooling system.
A detector that is activated by a rise of temperature is:
Welding and burning are two operations which give the highest risk of a fire on board ship. Which of the following safety precautions may be regarded as the most important in order to minimise this particular risk?
The area where the welding is to take place and adjacent spaces to be cleaned and all unnecessary materials and objects to be removed.
Only holders of a welding certificate should be allowed to carry out welding or burning on board ships.
Only use electrodes from a well known manufacturer.
Electric welding plants should be controlled by a responsible engineer before use.
Unfortunately an insect has become lodged in the ear. How to remove the insect?
By using rubber vacuum pump and suck the foreign body out.
Hold one hand across your nose and blow hard. Since the nose-channel is closed, the air will escape through the ears instead. And so will the foreign body.
Gently flood the casualty’s ear with terpid water so that the insect will float out.
By using a Q-tip and carefully try to get the insect out.
What is the minimum number of channels required for the portable two-way VHF’s for survival craft?
What do you understand by the order: “Move the pilot ladder to the other side”?
To shift the pilot ladder to the opposite side of the ship.
To move the pilot ladder further along nearer to the bow.
To change the position of the pilot ladder from the main deck to the fore deck.
To rig another pilot ladder.
Where does the excess steam discharge to when the boiler safety valves operate due to the boiler pressure being too high?
The atmosphere via the atmospheric line.
The threads on the drain plug for the bronze end cover of a sea water cooled heat exchanger have been badly damaged during maintenance. There is no spare brass plug available. What is the best solution for repairing the heat exchanger?
Make a new brass plug on the lathe to fit the drain hole.
Use a steel plug with the same thread as the original to replace it.
Wrap the threats in thread tape and coat it with jointing compound before refitting it.
Hammer in a wooden tapered plug as a temporary repair.
An engine room rating is assisting the duty engineer during a period of UMS operation. After completing the tasks they have been busy with the engineer and rating leave the engine room which is returned to UMS mode. The rating realises that an oil tank filling valve has been left open. What action should be taken?
Inform the duty engineer immediately so that the engine room can be re-entered and the valve can be shut.
Inform another crewmember that he is going back into the engine room to close the valve.
Just leave the valve open as it is unsafe to enter the engine room alone. The high alarm will sound to notify the engineer when the tank is full.
Re-enter the engine room straight away and shut the valve.
Give the meaning of the following symbol:
Muster station for unaccompanied minors (UM).
Personal protection equipment appropriate to the task should be worn during work in the engine room. Which of the tasks given in the options requires that safety goggles should always be worn?
When you are working with power tools or chemicals.
When you are filling in the engine room log book.
When you are tidying up in the engine room workshop.
The bones in the human body are connected to each other by:
Different type of joints.
During an oil cargo discharging operation, the IG supply to the tanks fails. As an OOW you would:
Continue discharging with the cargo pumps running at minimum speed, and inform the engine room.
Slow down and relieve the vacuum by opening the tanks lids and inform the Chief Officer.
Activate the inert fans and blow fresh air into the cargo tanks, and inform the terminal authority.
Immediately stop the discharging and inform the Chief Officer.
What would be the most probable cause of high temperature readings for the bearings in a diesel engine?
Lubricating oil pressure too low.
Charge air pressure too low.
Jacket cooling water temperature too high.
How many rocket parachute flares are carried in each liferaft with SOLAS B pack?
What should be the first action to be taken in the event of the water level disappearing out of the boiler water level gauge glass?
Close the main steam stop valve.
Secure all of the burners.
Close the feed water stop valve.
An engine room rating is assisting in the maintenance of some of the valves on the low pressure steam range. Which packing material, from the options given, would be the best choice for repacking the gland of a low pressure steam valve?
Lead covered cotton packing.
Where would you find out which fire sections are enclosed by “A” or “B” class divisions on a ship?
On the ship’s fire control plans.
On the general arrangement plan.
All the mentioned alternatives.
Is there any special area where it is forbidden to pump out any sludge or oil residues?
There are 8 special area where it is forbidden to pump out any sludge or oil residues.
There are 9 special area where it is forbidden to pump out any sludge or oil residues.
There are 4 special area the Baltic, Mediterranean, Red sea and Black sea where it is forbidden to pump out any sludge or oil residues.
There isn’t any special area where it is forbidden to pump out any sludge or oil residues.