Home Online tests CES Oil tanker Handling and Stowage Test for seamans about Cargo Handling and Stowage on Oil Tanker (CES v6.0)

Online testing: Test for seamans about Cargo Handling and Stowage on Oil Tanker (CES v6.0)

Select the test mode:

Education

Passing the test

Online test

Description

Reviews

The test consists of 80 random questions.
Total questions on this topic: 119

Question 1 from 80

Segregated Ballast Tanks on an oil tanker may best be defined as:

Cargo tanks which may be used for the carriage of ballast.

Cargo tanks which each have their own individual pumps, are fitted with independent piping systems and are served by unconnected ventilation arrangements.

Tanks which are completely separate from cargo or fuel oil systems, being permanently allocated to the carriage of ballast and fitted with their own pumps and associated piping.

Cargo tanks which may be used for ballast, where the lines are not connected to the Oil Discharge Monitoring Equipment.

When tank cleaning hoses are tested for electrical continuity, they must display a reading of:

Not greater than 6 ohms per metre length.

I don’t know.

At least 8 ohms per metre length.

Not more than 10 ohms per metre length.

Under the ISM Code the provision of individual control measures for specific work-related tasks exist in the:

Definition of supervisory responsibilities.

Documentation of individual job descriptions.

Permit to Work system.

Due diligence clause.

Which of the following best describes what the wax content of crude oil is?

The percentage of wax, expressed as a percentage, remaining in an oil product after distillation.

The percentage, by weight, of paraffinic wax found in a representative sample of the crude oil.

I don’t know.

The observed volume percentage of waxy deposit found in a cargo tank after discharge in relation to the total volume of cargo previously carried.

When conducting a risk assessment for a shipboard work activity, the two elements to be considered are:

The chance of an incident re-occuring and the potential effects of an loss.

The available manpower and their experience in this type of work.

The potential severity of harm and the likelihood that harm will occur.

I don’t know.

When discharging dirty ballast from an oil tanker at a high flow rate with main cargo pumps, the instantaneous rate of discharge of oil is calculated by formula:

Instantaneous rate of discharge (l/nm) = oil content (ppm) · flow rate (m3/h) / speed (knots) · 1 000.

Instantaneous rate of discharge (l/nm) = oil content (ppm) · 1 000 / flow rate (l/h) · speed (knots).

Instantaneous rate of discharge (ml/nm) = oil content (ml/nm) · flow rate (l/m) / speed (knots) · 100.

I don’t know.

The purpose of expansion couplings to be fitted on the longitudinal pipelines of oil tankers is:

To allow the pipelines to follow the ships flexing movement when pitching.

To allow the pipeline to expand when loading a hot cargo through the pipeline.

To prevent the pipeline from cracking when the ship suffers from Racking stresses.

I don’t know.

You are on a sailing vessel, underway in open water. This vessel is sighted on the starboard bow, on a steady bearing and the distance is closing. By the International Regulations for the Preventing Collisions at Sea, what action will you follow?

Risk of collision is deemed to exist and, as the other vessel is on a steady bearing on my starboard side, I will maintain my course and speed.

This vessel is clearly a power-driven vessel and I anticipate that the bearing will therefore close and she will pass ahead at a safe distance.

Risk of collision is deemed to exist and, as the other vessel is on a steady bearing on my starboard side, I am required to keep out of the way. I will make a broad alteration of course to starboard.

By Rule 18, a power-driven vessel underway shall keep out of the way of a sailing vessel. I will maintain my course and speed, but will continue to monitor situation to ensure the other vessel takes avoiding action.

Which of the following type of crude oil requires special consideration in terms of carriage and cleaning?

Reconstituted Crude.

Medium Crude.

Paraffinic Crude.

Sweet Crude.

The purpose of permanent continuous coamings fitted from side to side across the decks near the accommodation of an oil tanker is:

To keep deck spills away from the accommodation and service areas.

To reduce the effects of racking stresses.

To push the sea water shipped onto the deck over the sides of the ship.

To increase the strength of the deck structure.

When commencing the cargo transfer at the terminal, the decision to commence the transfer is made by:

The mutual agreement of those in charge of cargo operation, both on board and ashore.

The person in charge of cargo operation at the terminal.

The person in charge of the chartering and operation of the vessel.

The person in charge of cargo operation on the vessel.

On oil tankers, Cargo tanks can be isolated from machinery spaces by:

All the answers are good.

Pump room.

Cofferdams.

Ballast tanks.

As per the IMDG Code, “Proper Shipping Name” is defined as:

The correct chemical name of a potentially hazardous material, as identified from the Chemical Cargo List.

The name under which a dangerous material, substance or article is described for export purposes in the country of loading.

The name assigned by the manufacturer to a material, substance or article for the purposes of shipment.

The name to be used in any documentation relating to the transportation of the dangerous substance, material or article, such as on forms, labels and placards.

When in-service testing a hose used for cargo transfer on an oil tanker (and for which the elongation of the hose assembly when new was greater than 2,5 %), the maximum permitted elongation before the hose must be withdrawn from service should be:

Not more than 1,5 times the temporary elongation measured at the previous in-service test, as documented in the ship’s annual test record.

Not more than 1,25 times the temporary elongation measured when the hose assembly was last tested, as documented in the appropriate certificate.

Not more than 1,5 times the temporary elongation measured when the hose assembly was last tested, as documented in the appropriate certificate.

Not more than 1,5 times the temporary elongation measured when the hose assembly was new, as documented in the manufacturer’s certificate.

The compensation payment by the charterer that is due when a vessel is unable to load/discharge her cargo within the allowed and contracted time is referred to as:

Contractual penalty discount.

Discretion.

Demurrage.

Deferment.

The ODME printed record for ballast water discharge overboard from the cargo piping system on oil tankers operations must be retained on board for a minimum period:

Of 3 years.

I don’t know.

Of 2 years.

Of 1 year.

To correctly report an oil spill in US waters:

The master of the vessel responsible for the spill must advise the Environmental Protection Agency National Incident Reporting Center (or the appropriate regional office) within 2 hours of the incident being reported to that person.

The person in charge must first report the spill to the National Response Center or, if not practicable, to the Environmental Protection Agency regional office or local US Coast Guard Marine Safety Office. This must be done immediately that person has knowledge of the spill.

The person responsible for the spill must report preliminary details to the appropriate State Police within 30 minutes of the accidental discharge taking place.

I don’t know.

Where would you find the document relating to the “Condition of Freeboard Assignment” onboard?

With the Safety Construction Certificate.

With the Classification Records.

With the Loadline Certificate.

With the Structural Survey File.

What are the three volumes of the IAMSAR Manual?

A – Command and Control; B – Communications; C – Rescue Procedures.

I – Planning and Preparation; II – Rescue Control; III – Reference.

I – Organization; II – Communications; III – Rescue Procedures.

I – Organization and Management; II – Mission Co-ordination; III – Mobile Facilities.

The longitudinal bending moments caused by cargo distribution on an oil tanker need to be taken into consideration:

Only during loading and discharging cargo.

Only when on ballast passage in heavy seas and when the vessel is pitching.

Only when on loaded passage in heavy seas and when the vessel is pitching.

During loading, discharging and on loaded passage.

With reference to the exposure of “vapours” from oil cargoes, “Short Term Exposure Limit” value is determined by:

The airborne concentration of a toxic substance averaged over any 10 minute period, usually expressed in ppm.

The airborne concentration of a toxic substance averaged over any 15 minute period, usually expressed in ppm.

The airborne concentration of a toxic substance averaged over any 25 minute period, usually expressed in ppm.

The airborne concentration of a toxic substance averaged over any 30 minute period, usually expressed in ppm.

As per MARPOL, Oil Record Book Part II, Cargo/Ballast Operations, must be carried and completed on oil tankers of:

150 gross tonnes and above.

I don’t know.

20 gross tonnes and above.

50 gross tonnes and above.

The maximum oxygen content by volume permitted in the cargo tanks throughout the crude oil washing operation is:

10 %.

5 %.

3 %.

8 %.

According to 33 CFR 156.170, for oil tankers trading in US waters, the minimum requirement for testing of cargo transfer hoses and associated piping system are:

That no leakage occurs under dynamic fluid pressure of less than 1,5 times the maximum allowable working pressure.

That no leakage occurs at the nominal anticipated working pressure.

That no leakage occurs under static liquid pressure of at least 1,5 times the maximum allowable working pressure.

I don’t know.

The purpose of the demister unit within the Inert Gas System is:

To remove water from the IGS stream.

To remove sulphur oxides.

To cool the inert gas.

To prevent overheating.

Your vessel is in an area of restricted visibility. You hear this sound signal. What does it mean?

That there is a vessel in distress nearby.

That there is a vessel engaged in underwater operations in the vicinity. She has divers down.

That there is a vessel at anchor in the vicinity.

That there is a vessel aground in the vicinity.

The purpose of the “mud box” fitted on a tanker is to:

Collect ships waste and water mud when ballasting and de-ballasting.

Catch the mud from the anchors and cables and deposit these at the windlass.

Restrict any particles and solids entering the pipeline system.

Catch spills when connecting the discharge or loading hose.

When an inhibitor is added to an oil cargo, the items mentioned on the accompanying certificate include:

Inhibitor name; amount added; date added; period of efficiency; precautions if voyage length exceeds that period; eventual temperature limitation.

Inhibitor class; amount added; date of expiry; minimum period of optimum efficiency; precautions to be taken when added; minimum temperature requirement.

Inhibitor name; percentage applied; date of expiry; precautions to be taken on voyage and interval of application; maximum temperature at which continuously effective.

Inhibitor class; percentage blended; date added; maximum period of efficiency and applicable temperature limits; maximum storage period on board; contact number of manufacturer.

Crude Oils required by MARPOL to be specifically listed in a tanker’s Crude Oil Washing manual as unsuitable for COW are:

Those with highbenzene content.

Those with high pour point of viscosity.

Those with high basic sediment and water content.

I don’t know.

After the last entry being made, the retention period of an oil record book on board must be:

Not less than 5 years after the date of the last entry.

I don’t know.

Not less than 3 years after the date of the last entry.

1 year.

I don’t know.

Not more than 1,5 times the temporary elongation measured at the previous in-service test, as documented in the ship’s annual test record.

Not more than 1,5 times the temporary elongation measured when the hose assembly was new, as documented in the manufacturer’s certificate.

Not more than 1,25 times the temporary elongation measured when the hose assembly was last tested, as documented in the appropriate certificate.

What is a VPR (OPA-90)?

Vessel Response Plan.

Vessel Report Plan.

Vessel Response Procurement.

I don’t know.

On board a crude oil tanker, guidance on the washing system and equipment along with the applicable operating procedures, can be found in:

The Oil Record Book – ship particulars page.

The Operating and Equipment (COW) Manual.

The ODME Operating Manual – manufacturer’s instruction section.

MARPOL – Annex I.

As per MARPOL, the formula for calculating the minimum draft amidships for crude tankers in ballast condition is:

2,0 + 0,02 L.

I don’t know.

2,0 + 0,015 L.

2,0 + 0,002 L.

What is the density of the undiluted vapour that is liberated from crude oil?

1,5 times that of inert gas.

I don’t know.

It doesn’t matter.

2 times that of inert gas.

With reference to ship stability, the letters “TPC” stand for:

Tonnes per Centimetre Immersion.

Tonnes per Centimetre.

Tipping Perimeter Centre.

Trim per Centimetre.

The compensation payment by the charterer that is due when a vessel is unable to load/discharge her cargo within the allowed and contracted time is referred to as:

Demurrage.

Contractual penalty discount.

Deferment.

Discretion.

With reference to oil tanker equipment, the abbreviation VECS stands for:

Vapour Ejection Control System.

Vapour Emission Calibration System.

Vapour Emission Control System.

Vapour Emission Control Standard.

Crude oils may be considered to consist:

A natural mixture of carbon and sulphur isomers.

A refined blend of hydrocarbon compounds and sulphur extracts.

A mixture of carbon extracts and naturally occurring wax.

A natural mixture of simple and complex hydrocarbon compounds.

How many square metres does the IAMSAR Volume 3 manual suggest may be calmed by releasing 200 litres of lubricating oil slowly through a rubber hose with the outlet maintained just above the surface while the ship proceeds at slow speed?

Approx 500 square metres.

Approx 5 000 square metres.

Approx 50 square metres.

Approx 50 000 square metres.

With reference to oil cargo characteristics, “cloud point” is:

I don’t know.

The temperature at which an oil product begins to emit vapours which can be observed in a spectroscope due to the volume of solid particles extracted during evaporation.

The depth within a cargo above which no waxy solids are entrained.

The temperature at which a liquid hydrocarbon begins to congeal and take on a cloudy appearance, due to the bonding of constituent paraffin compounds.

As per SOLAS the Inert Gas System of an oil tanker must deliver the inert gas with a maximum level of oxygen of:

Not less than 8 % by volume.

Maximum 3 % by volume.

Not more than 5 % by volume.

Between 8 % to 11 % by volume.

Special Areas as per MARPOL are:

Specific geographical sea areas in which special mandatory measures for the prevention of sea pollution by oil are required.

Specific geographical sea areas, designated as Marine Conservation Areas by the United Nations, in which any discharge from the cargo area of an oil tanker is strictly controlled.

All sea areas within 50 miles from the nearest land, where that coastal state is a signatory to MARPOL.

Limited ocean and sea areas, listed under the OPA-90 Act, inside which the discharge of oil is prohibited and the penalty for doing so is an unlimited fine and jail sentence.

Depending on the API, an error measurement of 0,1 degree Fahrenheit in a tank containing 300 000 barrels of oil will result in which of the following volumes?

50 barrels.

150 barrels.

300 barrels.

25 barrels.

The purpose of the decanting line between two slop tanks, where fitted, is:

To enable most of the recovered oil to be retained in the primary slop tank, while the cleaner part of the water will flow into the secondary slop tank, where it can be re-used as wash-water.

To avoid a build-up of static electricity during water washing, caused by air being drawn in as the primary slop tank empties.

To enable the filling of the secondary slop tank via the primary slop tank.

To enable both the primary and secondary slop tank to be filled without using the main cargo lines.

Besides danger of vapour inhalation by crewmembers, if Hydrogen Sulphide is present in high concentrations in crude oil, it can also cause:

Polymerisation.

Acid build-up.

Settling and layering.

Corrosion.

The reporting of incidents involving harmful substances and/or marine pollutants is regulated under:

Annex II to SOLAS 1974.

Protocol I of MARPOL.

The UN Convention on the Reporting of Accidents and Incidents which Present a Hazard to the Marine Environment 2004.

Appendix B of the Supplement to the IMDG Code

Master of every ship must provide:

Facilities to conduct training whenever required by the training officer.

A link between the shipboard training officer and the company training officer ashore.

The training during crews working hours only.

Proper rest to the crew after each training programme.

When internally transferring any oil cargo within the vessel, the correct procedure would be to:

Obtain permission from the receivers and retain all e-mail correspondence for the attention of the cargo surveyors.

Transfer no more than 5 % of the total cargo volume at any one time.

Obtain permission from the charterers and document all operations fully in the Oil Record Book.

It is not necessary to obtain any permissions, provided the Captain makes an entry in the Deck Log Book, documenting his reasons for moving cargo.

Ship’s cargo pump room alarm must be automatically activated when levels of hydrocarbon gas concentration are:

No higher than 10 % of LEL.

No higher than 5 % of LEL.

No higher than 15 % of LEL.

I don’t know.

What is the purpose of girders in the tank?

They support the stiffeners.

They transfer all sea forces acting on the plating.

They transfer all the cargo forces acting on the plating.

They support the stiffeners and also take up some of the sea forces.

As per IMDG Code, the term “separated from” can be defined as:

I don’t know.

Either in a vertical or horizontal separation: if the intervening decks are not resistant to fire and liquid, then only in a longitudinal separation is acceptable. For “on deck” stowage, this means a distance of at least 12 metres. This distance also applies to one package stowed “on deck” and another in an upper compartment.

In different compartments or holds when stowed “under deck”. Provided an intervening deck is resistant to fire and liquid, a vertical separation may be accepted as equivalent. For “on deck” stowage, this segregation means a distance of at least 6 metres.

With an intervening compartment, being both a vertical and horizontal separation. Provided an intervening deck is resistant to liquid and fire, a vertical separation of 6 metres is acceptable. For “on deck” stowage, this segregation means a distance of at least 12 metres irrespective of compartment divisions.

Any person who can assume overall charge of the ships crude oil washing operation must have:

They must have at least six months experience on tankers, be knowledgeable of the cleaning procedures and equipment applicable on board the vessel and be able to fully demonstrate understanding of the operation of the ODME equipment.

At least 12 months appropriate experience on oil tankers, have participated in at least two COW programmes and be fully knowledgeable of the contents of the Operations and Equipment Manual.

I don’t know.

They must have at least three months experience on tankers, have participated in at least six washing operations and be aware of the procedures associated with the completion of the Oil Record Book.

The approximate Upper Flammable Limit of Crude Oil when measured as a percentage volume in air is:

12,6 %.

15 %.

2,2 %.

9,5 %.

A tanker in ballast, having recently left the discharge port is involved in a collision. The two vessels are still interlocked after the collision and a survey of the ships gives all crew members are safe and the damage is focussed to the vicinity of the impact. What should be the greatest concern at this time?

When the two vessels separate one (or both) of the vessels will have insufficient stability to remain afloat.

The vessels moving together will create even greater damage to their structures.

The possibility of pollution.

The ships moving together in the swell/seaway will cause a spark and consequently an explosion.

Substances, materials and articles shall be stowed as indicated in the Dangerous Goods List of the IMDG Code, in accordance with a series of stowage categories, which are designated as:

5 categories, labelled A-E.

Three categories, numbered I, II and III.

10 categories, lattered A-K (excluding I).

10 categories, numbered 1-10.

After passing through the scrubbing tower of an inert gas system, the approximate level of carbon dioxide in the inert flue gas should be:

3 %.

21 %.

1 %.

13 %.

DG placards shall be located on a freight container:

One on each end and one on each side.

One on each side (only).

One on each end (only).

One of the back end and one on one of the sides (only).

When cargo discharge reaches stripping levels on an oil tanker, it is necessary to reduce the inert gas pressure so as to:

Comply with the requirement of MARPOL Annex VI.

Avoid over-capacity in the IG generator.

Avoid locking the cargo pump impeller.

Minimise blowback.

What is this?

The United Nations stamp used for endorsing international shipping certificates.

The United Nations Packaging symbol used for Dangerous Goods.

The identification stamp placed in the passport of a stowaway by an Immigration Officer to indicate that his or her nationality is “unknown”.

The “Unitary Nomenclature” symbol placed alongside the name of a dangerous cargo in shipping documents to indicate that it appears on the list of approved international shipping names.

As per IMDG Code, the main criteria for drawing up classes for safe handling of hazardous substancesis on the basis of:

I don’t know.

Selective laboratory tests commissioned by the Committee.

Chronological order in which they have been assessed.

The type of hazard they present.

The one particular hazard to be taken care against, when using portable steam driven blowers for ventilating oil cargo tanks is:

That plastic extension tubes should not be used, in case the top collar overheats and melts, causing the tube to drop into the tank.

That prolonged use may cause the core material of the fan to heat up to a point where it may become a source of ignition.

That the steam outlet must point vertically upwards to avoid possibly burning the legs of passing personnel.

That the exhaust does not vent into the cargo tank, in order to prevent possible build-up of static electricity.

At which of the following concentrations of Hydrogen Sulphide might a person experience dizziness, fatigue and memory loss?

40 ppm.

20 ppm.

10 ppm.

I don’t know.

As per the IMDG Code, an “article” is referred to as:

Something that is packed within a freight container.

A device that is responsible for initial dangerous reaction.

A device that contains a dangerous substance or mixture of substances.

A form that contains important information about a hazardous substance.

Prior carrying out a Crude Oil Washing operation, the tank from which the crude is to be used for washing is usually partially discharged. This is done so as to:

Ensure that all water settled in the tank is removed prior washing, so as to ensure that the fresh cargo can be loaded on top without fear of contamination.

Ensure that only the required quantity of oil are kept in the tank, so as to reduce the amount of slops retained on the ship.

Ensure that any settled water is removed from the tank and only “dry” crude is used for washing so as to avoid electrostatic hazards during washing.

What is the relationship between absolute pressure and gauge pressure?

Absolute pressure = gauge pressure.

Absolute pressure = gauge pressure – atmospheric pressure.

I don’t know.

Absolute pressure = gauge pressure + barometric pressure.

The inert gas system shall be capable of delivering inert gas to the cargo tanks at the rate of:

No such requirement.

At least 125 % of the maximum discharge capacity.

At least 135% of the maximum discharge capacity.

At least 150 % of the maximum rate of discharge capacity.

If for some reason a vessel does not comply with a Classification Society’s requirements, what can a surveyor issue to the vessel enabling it to sail to the next port or for a period of time?

A Notification of Deficiency.

A revised Class Notation.

A Condition of Class.

A notification of Detention.

The recommended guideline for avoiding the risk of electrostatic potential in a mist produced by using oil and water during Crude Oil Washing operations is that:

Crude Oil Washing, where the oil source is stored in a slop tank or other tank that has previously contained slops, should be avoided.

I don’t know.

Before washing begins, any tank that is to be used as a source of oil for Crude Oil Washing should be partly discharged to remove any water that has settled out during the voyage. The discharge of a layer of at least 1 metre is necessary for this purpose.

If a slop tank is to be used to supply oil to drive a Crude Oil Washing operation in a cargo tank, then that slop tank must not have contained slops with a water content of more than 2 %.

Oil tankers of 70 000 tons and above, delivered after 31 December 1979 shall be:

No requirement regarding number of slop tanks.

Shall be provided with at least 2 slop tanks.

I don’t know.

Shall be provided with slop tank.

Oil tankers are subject to cyclical bending moments throughout their life as a result classification society rules require a specific minimum reduction in steel thickness to be maintained within “x” length amidships, where “x” is:

0,4 length.

I don’t know.

0,2 length.

0,3 length.

Within the Oil Discharge Monitoring and Control System, an “overboard discharge control” is defined as:

A device which automatically initiates the sequence to stop the overboard discharge of the effluent in alarm conditions and prevents the discharge throughout the period the alarm prevails.

A system which monitors the discharge into the sea of oily ballast or other oil-contaminated water from the cargo tank areas.

A facility which prevents the initiation of the opening of the discharge valve or the operation of other equivalent arrangements before the monitoring system is fully operational.

A system which receives automatic signals of oil content, flow rate, ship’s speed, ship’s position, date and time.

After efficient scrubbing of inert flue gas what would be the concentration of sulphur dioxide be:

25 ppm.

100 ppm.

50 ppm.

10 ppm.

As per the US Code of Federal Regulations, the current Oil Transfer Procedures for a vessel carrying out discharge in US ports must be:

That the procedures be legibly printed in a language or languages easily understood by personnel engaged in the transfer operation and permanently posted or available at a place where crew members can see and use them.

That the Master of the vessel engaged in a transfer shall, before commencing any transfer operation, ensure that all crew members involved in that operation shall be familiar with the applicable operating and emergency procedures and be capable of communicating in a common language with terminal operators.

That the procedures be available in hard-copy or electronic format to the Supervising Officer in a language with which he is familiar.

That the procedures be printed in the English and Spanish languages and permanently posted in the wheelhouse of the vessel.

Prior to discharging cargo from an oil tanker, “line displacement” is usually conducted to:

To balance a rigid cargo arm.

I don’t know.

The calibration of the ship’s flow meter.

Verify the pipeline contents with previous grade have been replaced.

According to SOLAS, the mechanical ventilation system of the cargo pump room shall be capable of making:

I don’t know.

At least 10 air changes per hour.

At least 20 air changes per hour.

At least 6 air changes per hour.

As per the IMDG Code, an “article” is referred to as:

A device that contains a dangerous substance or mixture of substances.

A device that is responsible for initiating a dangerous reaction.

A form that contains important information about a hazardous substance.

Something that is packed within a freight container.

During Crude Oil Washing, those areas of the cargo tanks which are not directly struck by the oil jet from the tank washing machines are referred to as:

Hidden areas.

Protected areas.

Deflected areas.

Shadow areas.

The maximum permitted oxygen content in the inert gas supply when inerting a cargo oil tank prior to gas freeing is:

8 % by volume.

12 % by volume.

5 % by volume.

I don’t know.

The Reid Vapour Pressure (RVP) test is commonly used for measuring:

The absolute vapour pressure of the liquid at 37,8 °C.

The absolute vapour pressure of the liquid at 15,6 °C.

The absolute vapour pressure of the liquid at 38,7 °C.

The absolute vapour pressure of the liquid at 59 °C.

The «Cargo Handling and Stowage, Management, Oil Tanker» subject provides both theoretical and practical knowledge on safely working with electrical equipment. Mastery of this material is a key indicator of an employee’s competence in their role aboard a vessel. Cargo handling and stowage on an oil tanker involve the processes of loading, unloading, and storing liquid cargo, such as crude oil or petroleum products. These operations require meticulous planning, strict adherence to safety protocols, and compliance with industry regulations to ensure the safe and efficient transportation of liquid cargo.

Version: 4.1, 5.0, 5.1, 6.0.0, 6.0.8, 6.0.10.
Test type: STCW.
Department: Cargo Handling and Stowage.
Level: Management.
Vessel type: Oil Tanker.

Only seamen can leave reviews. To leave a review, log in to the site with a seaman's account.

Be the first to review this online test!