Home Online tests CBT Anchor Handling MASTER / Ch-Officer Test Online about Deck Safety for Supply Vessels and for Anchor Handlers (CD 0334, 0335) (CBT)

Online testing: Test Online about Deck Safety for Supply Vessels and for Anchor Handlers (CD 0334, 0335) (CBT)

Select the test mode:

Education

Passing the test

Online test

Description

Reviews

The test consists of 80 random questions.
Total questions on this topic: 88

Question 1 from 80

How is the risk of slipping on a wet walkway reduced? Select the ONE best answer.

By having a non-slip coating.

By spreading salt on it.

By brushing the water off it.

By not walking on a wet deck.

For their safety, what should deck crew do as soon as a load is lowered onto the deck of a platform supply vessel? Select the ONE correct answer.

Confirm that the load will not be raised again.

Un-hook it immediately.

Check the contents of the cargo skip.

Check the cargo container number.

Choose the ONE option that best completes the following statement. A natural risk taker …

… is as safe as any other person.

… puts themselves in more danger.

… is an efficient worker, because they get the job done quickly.

… is representative of most people at sea.

There is the possibility of water breaking on deck. When should crew go onto the deck? Select the ONE best answer.

When the bosun gives the word.

Only when the bridge gives them permission.

As soon as a permit to work has been issued.

As soon as the risk assessment is completed.

When using a windlass for mooring, what is the most important safety priority? Select the ONE correct answer.

To have a person at the windlass control at all times.

To make sure that the hydraulic oil is warmed up.

To only use one side of the windlass at a time.

To have the windlass in a low gear at all times.

Select the ONE best answer relating to the following statement. When tying up a supply vessel , it is safe to jump onto the jetty, from the bulwark of the vessel.

The statement is incorrect. This practice is only safe for experienced crew.

The statement is correct, but only if the correct footwear is used.

The statement is incorrect. This practice can be very dangerous.

The statement is correct. It can save a lot of time.

How is effective communication achieved? Select the ONE correct answer.

By only using radio communication between two people.

Using a limited number of hand signals to avoid confusion.

Using a correct, common language.

By leaving the spoken communications to the vessel’s bridge.

What are the risks when using burning gear to break an anchor chain? Select the ONE best answer.

Burns, eye and hearing damage.

That the chain cannot be broken.

Burns, eye damage and fire.

That there is insufficient gas to complete the operation.

Choose the ONE option that best completes the following statement. When a crane driver is working the deck of a supply vessel, crewmen …

… should clear the deck totally.

… should stand in the place where the load has to be lowered.

… should stand close to where the load has to be lowered.

… should stay in sight of the crane driver.

When heaving a synthetic fibre mooring rope on a drum end, how many turns should there be? Select the ONE correct answer.

No more than three.

No more than four.

No more than two.

No more than five.

Which of the given options best defines “complacency”? Select the ONE best answer.

Complacency only occurs with people who are not seafarers.

Complacency is when a person deliberately decides not to follow procedures.

Complacency is when a person feels secure or smug in their ability to perform a task.

Complacency happens to a person when they have to undertake a task that is not a routine activity.

When undertaking routine deck work, what are the basic requirements for a crewman to stay safe? Select the ONE best answer.

Only work on deck when conditions are perfect.

Let others undertake the more risky work.

Being in a fit state, risk assessing and wearing PPE.

Following instructions from the bosun at all times.

Why does skills’ training not change a person’s attitude to risk? Select the ONE correct answer.

Because once attitudes are formed they cannot be changed.

Because people tend to ignore training.

Because skills’ training does not always address changing behaviour.

Because skills’ training will never include the risks associated with it.

What are the safety risks associated with dropping an anchor? Select the ONE best answer.

The anchor cable may run too fast.

The anchor may not be dropped in the correct place.

None, as it is such a routine, uncomplicated operation.

There are risks associated with moving equipment and rust particles.

Choose the ONE option that best completes the following statement. A simple method of guiding crew away from deck obstructions …

… is to have plans posted up in the mess rooms, showing the obstructions.

… is to paint the deck with a bright colour.

… is to keep crew off the decks.

… is to have dedicated walkways laid out on the decks.

On the deck of a supply boat working an installation, why is water on deck particularly dangerous? Select the ONE best answer.

Because the deck crew run the risk of getting wet.

A crush risk exists from floating containers.

The water affects the crane driver’s ability to stow cargo.

It causes the cargo to get wet.

When buoy catching, how are the risks associated with the open stern totally controlled? Select the ONE best answer.

Use a boat hook to extend your reach.

Wear a lifejacket and safety restraint.

Wear a lifejacket.

Do not work close to the stern.

Choose ONE option that correctly completes the following statement. When undertaking work at height …

… tie yourself on, once you are at the work place.

… never use tools.

… always wear a harness and fall protection.

… complete the work as quickly as possible.

There is the possibility of water breaking on deck. When should crew go onto the deck? Select the ONE best answer.

As soon as the risk assessment is completed.

As soon as a permit to work has been issued.

When the bosun gives the word.

Only when the bridge gives them permission.

Choose ONE option that best completes the following statement. When a cargo item is suspended above the deck…

… never be on deck with it there.

… never be underneath it.

… approach it, to catch the tag line.

… approach it, ready to get hands to position it.

Choose ONE option that correctly completes the following statement. When undertaking work at height …

… tie yourself on, once you are at the work place.

… never use tools.

… always wear a harness and fall protection.

… complete the work as quickly as possible.

How is it possible to let a vessel go without having men ashore? Select the ONE best answer.

By having the mooring lines on bights.

By cutting the mooring lines at the vessel’s fairleads.

By using a boat hook to lift the eye off a shore bollard.

By letting the moorings go and leaving them behind.

When undertaking routine deck work, what are the basic requirements for a crewman to stay safe? Select the ONE best answer.

Only work on deck when conditions are perfect.

Let others undertake the more risky work.

Being in a fit state, risk assessing and wearing PPE.

Following instructions from the bosun at all times.

What safety check is required on a wire or chain deck stopper before it is used? Select the ONE correct answer.

That the rotating guide is well greased.

The insert is well grooved from previous use.

The insert is in good condition and of the correct size.

That the insert will allow the chain or wire to pass through it.

When working cargo on deck, with the possibility of water breaking onto it, how can crew protect themselves? Select the ONE correct answer.

By sheltering amongst the cargo stow.

By refusing to go on deck to work cargo.

By remaining in safe areas or the accommodation as much as possible.

By only working deck cargo and avoiding hose work.

What danger is posed by equipment, with wire connected, about to be lifted? Select the ONE best answer.

The wire may whip around when the equipment is lifted.

The wire may fall off before the cargo is ashore.

The equipment may be damaged.

The wire may be very long.

If a platform discharge falls on the deck of a supply vessel with crew present, what should they do? Select the ONE correct answer.

Find out what the discharge is, and then act accordingly.

Clear the deck and report to the Bridge.

Proceed directly to the deck shower.

Accept that this sometimes happens, and stay on deck.

Choose ONE option that correctly completes the following statement with respect to safety. Grapnels and ‘J’ hooks used for anchor handling …

… should be inspected in the same way as any other lifting equipment.

… are extremely robust and do not need testing or inspection.

… never carry much load, because all they do is snag wire or chain.

… last a very long time because they are made of cast iron.

Choose ONE option that best completes the following statement. When a pennant wire is being heaved …

… take the chance to have a clear up on deck.

… it is the most dangerous part of an anchor handling operation.

… stay in a safe place.

… stay close, to inform the bridge of its position in the stopper.

Choose the ONE option that best completes the following statement. A simple method of guiding crew away from deck obstructions …

… is to have dedicated walkways laid out on the decks.

… is to paint the deck with a bright colour.

… is to have plans posted up in the mess rooms, showing the obstructions.

… is to keep crew off the decks.

Why is it that people need to be regularly reminded about safety? Select the ONE best answer.

Because companies have to do this under their SMS obligations.

Because people can forget even basic safety principles.

Because people forget what they see as unimportant.

Because people generally have very poor memories.

Choose ONE option that best completes the following statement. An anchor handler moving in a seaway …

… makes deck work more risky.

… can easily be allowed for.

… adds to the excitement of being at sea.

… has no affect on deck working.

Select the ONE best answer relating to the following statement. When tying up an anchor handler, it is safe to jump onto the jetty, from the bulwark of the vessel.

The statement is correct. It can saves a lot of time.

The statement is incorrect. This practice is only safe for experienced crew.

The statement is correct, but only if the correct footwear is used.

The statement is incorrect. This practice can be very dangerous.

When working cargo on deck, with the possibility of water breaking onto it, how can crew protect themselves? Select the ONE correct answer.

By only working deck cargo and avoiding hose work.

By sheltering amongst the cargo stow.

By remaining in safe areas, or the accommodation, as much as possible.

By refusing to go on deck to work cargo.

Choose the ONE option that best completes the following statement. If there is a risk of water breaking on a vessel’s deck …

… only go onto deck between the waves breaking on it.

… only go onto deck when there is a lull in the weather.

… only go onto deck after risk assessment and permit to work.

… only go onto deck after telling the bosun that you are going.

What precautions should the deck crew take with an awkward shaped load, such as a rig anchor, just landed on deck by a crane? Select the ONE best answer.

Attach a lashing to it immediately.

Unhook it, then move other cargo against it.

Make sure it is stable before approaching it.

Immediately unhook it, the same as any other load.

What is meant by a mooring rope ‘snap back’? Select the ONE correct answer.

It is the affect when a rope is surged on a drum end.

It is a type of stopper used on the mooring deck.

The reaction of the rope when it parts.

The noise a rope makes when it is under lots of tension.

On the deck of an anchor handler working an installation, why is water on deck particularly dangerous? Select the ONE best answer.

A crush risk exists from floating containers.

The water affects the crane driver’s ability to stow cargo.

Because the deck crew run the risk of getting wet.

It causes the cargo to get wet.

Choose the ONE option that best completes the following statement. Before removing the cap from the deck connection of a supply vessel’s dry bulk system, always …

… tell the installation crane driver that this is about to be done.

… confirm there is no pressure before removing the cap.

… open the deck valve located on the connection.

… have the hose on deck ready to be connected.

Why do people need to be regularly reminded about safety? Select the ONE best answer.

Because companies have to do this under their SMS obligations.

Because people generally have very poor memories.

Because people forget what they see as unimportant.

Because people can forget even basic safety principles.

What can happen to a crane hook that brings the greatest risk to the crane on an installation? Select the ONE correct answer.

It can become foul and trapped on a vessel.

It can be out of sight of the crane driver.

It can accidently open when a load is suspended.

It can be damaged by the deck crew opening it incorrectly.

Choose the ONE option that best completes the following statement. Before removing the cap from the deck connection of a supply vessel’s dry bulk system, always …

… open the deck valve located on the connection.

… have the hose on deck ready to be connected.

… tell the installation crane driver that this is about to be done.

… confirm there is no pressure before removing the cap.

What safety check is essential when a wire has just been positioned in a deck stopper? Select the ONE correct answer.

That the quick release system works.

That the wire is securely in place.

That the wire is in good condition.

That the wire is not under tension.

When anchor handling in marginal weather, why is the work more risky? Select the ONE best answer.

Because the vessel’s engines are likely to stop.

Because the winches do not work as well as in good weather.

Because the rig jumps around a lot.

Because wires and chains have greater strain on them.

With regard to towing operations in following weather, choose the ONE option that best completes the following statement. Green water …

… may be breaking over the stern.

… on deck is fun, and not a big threat.

… is not a threat on a well found vessel.

… will never be breaking over the stern.

Choose the ONE option that best completes the following statement. If there is a risk of water breaking on a vessel’s deck …

… only go onto deck after telling the bosun that you are going.

… only go onto deck after risk assessment and permit to work.

… only go onto deck between the waves breaking on it.

… only go onto deck when there is a lull in the weather.

Choose the ONE option that correctly completes the following statement. Without proper control of an operation…

… safety might occasionally be reduced.

… safety can often be reduced.

… safety may sometimes be reduced.

… safety is reduced.

What is the best preparation for crew, to ensure their safety during an anchor handling operation? Select the ONE best answer.

Tell them to follow the bosun’s instructions at all times.

Make sure they are all on deck when the operation starts.

Make sure they are well briefed and knowledgeable.

Check their certificates to confirm that they are qualified.

Choose ONE option that best completes the following statement. A bulk hose laid across a supply vessel’s deck …

… will damage other cargo.

… is a trip risk, when crew are working near to it.

… is difficult to connect up to the vessel’s deck connection.

… will damage itself, as it contacts other objects on the deck.

Why does working cargo offshore pose a greater risk to crew, than working cargo onshore? Select the ONE correct answer.

When offshore there is less time to undertake the equipment transfer than onshore.

When offshore they do the cargo work, but in port that work is done by dock workers.

Because when offshore, the crane drivers are not as good as the ones onshore.

Because the offshore cranes are of poorer quality compared to the onshore cranes.

How is effective communication achieved? Select the ONE correct answer.

By only using radio communication between two people.

By leaving the spoken communications to the vessel’s bridge.

Using a limited number of hand signals to avoid confusion.

Using a correct, common language.

How is the risk from an installation crane hook controlled when it is at deck level, ready to be hooked on? Select the ONE best answer.

Always wear a pair of working gloves when handling it.

Stay away from it at all times.

Keep it in sight and in control at all times.

Tell the crane driver to lift the hook off the deck.

Choose ONE option that best completes the following statement. When towing on an anchor handler …

… stay well clear of the tow wire when on deck.

… only go onto the vessel’s forward deck.

… never go onto the vessel’s after deck.

… the tow wire has no affect on deck working.

How is the risk of slipping on an ice covered deck reduced? Select the ONE best answer.

By never walking on an ice covered deck.

By having a non-slip coating on the deck.

By spreading paper over the ice.

By spreading salt on the ice and allowing it to melt.

Why should crew avoid walking on top of deck cargo on a supply vessel? Select the ONE best answer.

Because the cargo owner objects to this.

To reduce the risk of slips, trips and falls.

To reduce the risk of damaging the cargo.

Because company procedures do not allow it.

With regard to mooring operations, choose the ONE option that best completes the following statement. Never stand …

… in the whip lash zone of a rope under tension.

… near the edge of the vessel in case of being hit by a heaving line.

… behind the person operating the winch.

… at the winch control when heaving on a rope.

Choose the ONE option that best completes the following statement. A simple method of guiding crew away from deck obstructions …

… is to paint the deck with a bright colour.

… is to keep crew off the decks.

… is to have plans posted up in the mess rooms, showing the obstructions.

… is to have dedicated walkways laid out on the decks.

What is the greatest risk if a bulk hose is over-pressurised? Select the ONE correct answer.

Being injured if the hose or coupling were to part.

The hose will become plugged with product.

The product will be damaged inside the hose.

The deck valves will be damaged with the pressure.

Choose ONE option that best completes the following statement. When a pennant wire is being disconnected …

… retreat to a safe place, as this is the most dangerous part of an anchor handling operation.

… be careful, in case it wants to rotate dangerously.

… the operation is without risk.

… have a crew person grip it, to stop it rotating.

What is the worst possible consequence of an over pressurised hydraulic windlass motor? Select the ONE best answer.

None, as the pressure will never be too great.

The windlass motor may stop working.

The casing may blow apart.

The hydraulic oil will get hot.

How are the risks associated with disconnecting a bulk hose controlled on a supply vessel? Select the ONE correct answer.

Drain the product using the deck bleed valve, then disconnect.

Disconnect the hose and send it up as soon as possible.

Drain the product back and replace the hose end cap, if available.

Disconnect the hose and keep the open end upright on the crane hook.

Which one of the given options best defines ’complacency’? Select the ONE best answer.

Complacency only occurs with people who are not seafarers.

Complacency happens to a person when they have to undertake a task that is not a routine activity.

Complacency is when a person feels secure or smug in their ability to perform a task.

Complacency is when a person deliberately decides not to follow procedures.

Choose the ONE option that correctly completes the following statement. Without proper control of an operation …

… safety might be reduced.

… safety can be reduced.

… safety is reduced.

… safety may be reduced.

What extra safety measures should always be taken during darkness on a vessel whilst anchor handling? Select the ONE best answer.

Ensure that decks are well lit.

Wear extra clothing as it gets cold.

Shut the cabin curtains to stop light pollution.

Wear full PPE.

Choose ONE option that correctly completes the following statement. When undertaking work at height …

… tie yourself on, once you are at the work place.

… never use tools.

… always wear a harness and fall protection.

… complete the work as quickly as possible.

Why does skills’ training not change a person’s attitude to risk? Select the ONE best answer.

Because skills’ training does not always address changing behaviour.

Because people tend to ignore training.

Because skills’ training will never include the risks associated with it.

Because once attitudes are formed, they cannot be changed.

On a supply vessel working at an installation, why should deck cargo stay lashed for as long as possible? Select the ONE best answer.

Because it saves having to re-connect lashings so frequently.

To stop it falling over if there is a sudden vessel movement.

Because cargo should always be lashed at sea.

Because it is company policy under the ISM code.

Choose ONE option that best completes the following statement. The greatest risk with a supply vessel’s dry bulk system is if …

… cement gets damp and starts to set in the lines.

… the wrong grade of cement has been loaded.

… the crew do not realise there is pressure in the system.

… cement gets damp and starts to set in a tank.

On a platform supply vessel, how are the risks associated with obstructions on the mooring deck controlled? Select the ONE best answer.

By wearing adequate footwear.

By walking very slowly.

By using dedicated walkways.

By wearing full PPE.

Choose the ONE option that best completes the following statement. A natural risk taker …

… is as safe as any other person.

… is representative of most people at sea.

… puts themselves in more danger.

… is an efficient worker, because they get the job done quickly.

What safety check is required on hand tools used during an anchor handling operation? Select the ONE best answer.

That they are identifiable as deck tools.

That they are approved for use.

That they are made in Germany.

That they are close at hand.

Choose ONE option that correctly completes the following statement. A remotely operated winch control …

… is not as safe as controlling the winch locally.

… offers more safety to the operator.

… is not a good thing, it decreases safety.

… is not found on anchor handling vessels.

On a platform supply vessel what should happen with dangerous cargo? Select the ONE correct answer.

It should not be accepted onboard.

It should always be stowed together with all other dangerous cargo.

It should be manifested and in a marked container.

It should be discharged as soon as possible.

Why is the size of the wire fitted to a tugger winch important for safety? Select the ONE correct answer.

Because the winch power should not be capable of snapping the wire.

To allow the wire to go to the stern and back up the deck with some spare.

Because the drum of the winch is usually quite small, the wire should be small.

Because if it is too big it is difficult to handle.

Why can a mooring rope being heaved on a windlass drum end be particularly dangerous? Select the ONE best answer.

Because the rope may snap back towards the person holding it.

Because there is little control of the rope.

Because the windlass may put excessive force on the rope.

Because the mooring deck is a dangerous place.

Choose ONE option that best completes the following statement. When a vessel sails out into bad weather, the anchors …

… can be left unsecured if the weather is expected to improve.

… will become loose and have the chains banging in the spurling pipes.

… have to be secured, even if the deck crew have to take some risks.

… should already be secured, or a safe heading and speed set to secure them.

On a platform supply vessel, how are the risks associated with the dry bulk system controlled? Select the ONE best answer.

By following operating procedures.

By being careful when opening lids and caps, in case there is pressure.

By first opening the deck valve, then the tank valve.

By only getting senior crewmen to operate it.

Choose the ONE option that best completes the following statement. When working with a crane hook on the deck of a supply vessel, for safety …

… always have two crewmen.

… always have three crewmen.

… only ever put one hose on the hook.

… always attach a tag line to it.

Choose ONE option that best completes the following statement. Supply vessel movement …

… has no affect on deck working.

… adds to the excitement of being at sea.

… can easily be allowed for.

… makes deck work more risky.

What is the most dangerous risk associated with cargo work on a supply vessel? Select the ONE best answer.

Falling over the side of a vessel.

A crush injury from an item of cargo.

Being burned on a hot surface.

Tripping over cargo lashings.

Тест охватывает вопросы безопасности на палубе, включая использование оборудования на судах снабжения и при работе с якорями.

Only seamen can leave reviews. To leave a review, log in to the site with a seaman's account.

Be the first to review this online test!