The test consists of 80 random questions.
Total questions on this topic: 300
При приеме лоцмана с катера следует подавать ему предохранительный пояс со страховочным канатом, если высота надводного борта судна более:
Толщина срезаемого слоя металла за один проход резца называется:
Передвижение по штормтрапу допускается при наличии:
Предохранительного пояса со страховочным канатом.
Штангенинструменты применяются для:
Приблизительных измерений.
Ручные электрические машины, электрический инструмент, ручные светильники и вспомогательное оборудование к ним подвергаются проверкам и испытанию не реже:
При какой температуре разрешается удаление воды из котла?
Сверлением можно получить отверстия точностью до:
На какой срок выдаются международные свидетельства МАРПОЛ?
При подготовке двигателя к пуску избежать гидравлического удара в цилиндре позволяет:
Продувка пусковых баллонов и пусковой магистрали.
Проверка уровня воды в расширительной цистерне.
Проворачивание двигателя валоповоротным устройством на 2-3 оборота.
Проворачивание двигателя пусковым воздухом при открытых индикаторных кранах.
Работу масляного фильтра в системе циркуляционной смазки дизеля контролируют:
По давлению за циркуляционным насосом.
По давлению в системе смазочного масла.
По перепаду давления до и после фильтра.
Если есть сомнение о наличии надлежащего уровня воды в котле необходимо:
Продуть водоуказательные приборы.
Немедленно прекратить горение.
Проверить уровень воды в котле открытием пробных клапанов.
Гомогенизация топлива проводится:
Для образования однородной структуры топлива.
Для очистки топлива от механических примесей.
Для удаления из топлива воды.
Для улучшения смесеобразования в камере сгорания.
Обработка поверхности после механической обработки путем соскабливания тонких слоев металла называется:
При работе со стальными и растительными канатами запрещается находиться и держать руки ближе чем __ от турачек, кнехтов, блокова.
Выпускные газы имеют белый цвет по причине:
Плохого качества топлива.
В цилиндры поступает много масла.
Ответственность за выполнение на судне комплекса мероприятий по предотвращению загрязнения с судов возлагается на:
Для разбавления масляных красок или олифы, ускорения их высыхания используется:
Если раскеп положительный, то подшипник данного мотыля должны быть:
Запорная арматура подпирается в зависимости от:
Объема проходящей через нее жидкости.
Условного диаметра прохода.
Уровня расположения относительно воды.
Для предотвращения случайного или намеренного сброса льяльных вод за борт с нарушением правил МАРПОЛ 73/78 в осушительной системе:
Закрывают и пломбируют отливную забортную арматуру.
Пломбируют нагнетательный клапан осушительного насоса.
Закрывают клапаны на льяльных колодцах.
Мерный инструмент, используемый в слесарном деле для снятия и переноса размеров детали на масштаб называется:
Рассверливание производят для:
Уменьшения шероховатости.
Причиной подрыва предохранительных клапанов во время пробных пусков двигателя является:
Максимальная температура питательной воды, подаваемой к инжектору, не должна быть выше:
Токарные станки применяются для:
Обработки плоских поверхностей.
Обработки прямолинейных канавок.
Точения наружных поверхностей вращающихся деталей.
При засорении сопловых отверстий форсунки производят:
Опрессовку форсунки на стенде.
Прочистку сопловых отверстий калиброванной проволокой.
Микрометрические инструменты позволяют производить измерения с погрешностью до:
Чистовая обработка отверстия после сверления или зенкования с целью получения высокой точности и чистоты поверхности называется:
Наиболее распространенный инструмент для обработки плоских, цилиндрических и фасонных поверхностей:
Укажите аббревиатуру Международной конвенции по предупреждению загрязнения с судов:
По каким параметрам можно судить о засорении фильтра?
Повышение перепада давления до и после фильтра.
Подтекание фильтрующего элемента.
Сильная вибрация фильтра.
Балластные цистерны судов с ледовыми усилениями оборудуются:
Системой авайриной откачки балласта.
Системой сжатого воздуха.
Подачу балластного насоса подбирают с таким расчетом, чтобы весь балласт судна откачивался за:
При обнаружении пропуска топлива в трубках высокого давления ТНВД и форсункой, следует:
Отключить ТНВД и заменить дефектную трубку, или подтянуть штуцерное соединение.
Установить поддон для сбора протечек.
Установить хомут на месте трещины.
Подтянуть резьбовое соединение штуцеров.
Какие меры следует принять при работе дизеля с перегрузкой?
Промасленная ветошь во время несения вахты или производства ремонтных работ должна собираться:
В металлический ящик с крышкой и отверстиями для вентиляции.
И немедленно выбрасываться за борт.
В специальный ящик без крышки.
В специальную емкость на верхней палубе.
Подбирать швартовные канаты разрешается:
После подтверждения с берега.
После закрепления каната на турачке.
После подтверждения капитана.
Как механик обязан проверить показания всех КИП дизелей?
При приеме и сдаче вахты.
После отхода судна от причала.
После аварийного происшествия.
Для предотвращения проникновения топлива в льяльные воды машинного отделения применяют:
Фильтры очистки льяльных вод.
Поддоны под механизмами и устройствами.
При обгорании, проявлении трещин и разрушении сопел форсунки производят:
В дизельном топливе допускается содержание воды:
Содержание воды не допускается.
В каком случае прекращается слив нефтесодержащих вод?
Если на поверхности воды появляются следы нефти.
В случае поломки оборудования.
В случае неисправности сигнализатора.
Процесс создания неразъемного соединения металлов с помощью присадочного связующего материала называется:
Температура масла при прогреве дизеля не должна превышать:
Уайт-спирит применяется для растворения:
Запрещения по сбросу сточных вод не применяются:
В случае одобрения сброса старшим механиком.
В случае обеспечения безопасности судна и находящихся на его борту людей.
В случае одобрения сброса Администрацией порта.
При упуске воды из системы охлаждения дизеля, заполнять систему можно только:
После отключения топлива.
Угол опережения подачи топлива в цилиндр определяется:
Положением кулачковой шайбы на распред. валу.
Регулировкой распылителя форсунки.
Силой натяжения пружины форсунки.
Длина цепного стопора для стопорения стальных канатов:
Где должны быть постоянно вывешены краткие инструкции по эксплуатации рулевой машины?
На ходовом мостике и в румпельном отделении.
На надстройке в кормовой части судна.
В машинном отделении вблизи с главным двигателем.
При работе с помощью грузоподъемных средств разрешается их закреплять:
К специальным рамам и элементам корпуса судна.
Температура охлаждающей пресной воды при прогреве двигателя должна быть:
Трещины, неплотности соединения картера обнаруживают по:
Покрасочные работы производят при температуре не ниже:
Лакировку выполняют при температуре:
Зенкерование применяется для:
Чистовой обработки отверстий.
Придания особых свойств материалу.
В рамовых и мотылевых подшипниках применяют антифрикционный материал:
Открывать картер дизеля для его осмотра или ремонтных работ можно не ранее, чем:
5-10 мин после его остановки.
Двигатель перестанет вращаться.
10-20 мин после его остановки.
Под термином “Квалитет” понимают:
Разницу между исходной заготовкой и готовой деталью.
Развертывание применяют для:
Уменьшения диаметра отверстия.
Увеличения диаметра отверстия.
Чистовой обработки отверстия.
В системе водяного охлаждения поршней двигателя наблюдается колебание давления, а температура воды на выходе из полости охлаждения одного цилиндра повышается.
Загрязнение охладителя поршневой воды.
Неисправность насоса охлаждения.
Трещина в головке поршня.
Сломано поршневое кольцо.
Попмаж турбокомпрессора связан с:
Уменьшением расхода воздуха через компрессор.
Отсутствием подачи воздуха на компрессор.
Увеличением расхода воздуха через компрессор.
Операцию возвращения кривым или погнутым металлическим изделиям первоначальной прямолинейной или другой формы называется:
В зависимости от класса точности станки делятся на:
Если судно в соответствии с положениями МАРПОЛ-73/78 освобождено от необходимости установки нефтеочистного оборудования, оно должно иметь:
Цистерны для накопления нефтесодержащих вод и системы для сдачи их на приемные сооружения.
Систему трубопроводов для сдачи нефтесодержащих вод на берег.
Индикатор запаса подсланевых вод.
Рабочим телом в ДВС является:
Основным элементом ТНВД является:
На какой срок допускается “мокрое” хранение котла?
Под сокращением ЧПУ подразумевают:
Червячное подающее устройство.
Частотный прерыватель управления.
Числовое программное управление.
Для крышек цилиндров характерным повреждением являются:
При отсутствии постоянного освещения рабочее место оснащают переносным освещением напряжением не выше:
Ударный инструмент, состоящий из металлической головки рукоятки и клина называется:
Обкатывание наружных поверхностей выполняется для:
Упрочнения поверхностного слоя детали.
Перед пробными пусками установки, работающей на винт регулируемого шага (ВРШ), необходимо лопасти винта установить в положение:
Положение нулевого винта.
Положение максимального переднего шага.
Положение фиксированного шага.
Винтовой зажим иначе называют:
Заходить в пространство между открытыми люковыми секциями:
Разрешается по указанию вахтенного помощника капитана.
Укажите предельную продолжительность работы дизеля на холостом ходу:
Укажите норму содержания нефтепродуктов при сбросе нефтяной смеси?
С чего следует начинать проверку валопровода перед пуском дизеля?
С проверки давления масла в системе.
С открытия главного пускового клапана.
С проверки отжатия тормоза.