Maison Tests en ligne CES Oil tanker Handling and Stowage Test for seamans about Cargo Handling and Stowage on Oil Tanker (CES v6.0)

Tests en ligne : Test for seamans about Cargo Handling and Stowage on Oil Tanker (CES v6.0)

Sélectionnez le mode de test :

Éducation

Réussir le test

Test en ligne

Description

Commentaires

Le test comprend 80 questions aléatoires.
Total de questions sur ce sujet : 119

Question 1 depuis 80

What is a VPR (OPA-90)?

Vessel Response Plan.

Vessel Report Plan.

Vessel Response Procurement.

I don’t know.

Besides danger of vapour inhalation by crewmembers, if Hydrogen Sulphide is present in high concentrations in crude oil, it can also cause:

Polymerisation.

Acid build-up.

Settling and layering.

Corrosion.

What is the density of the undiluted vapour that is liberated from crude oil?

1,5 times that of inert gas.

I don’t know.

It doesn’t matter.

2 times that of inert gas.

When internally transferring any oil cargo within the vessel, the correct procedure would be to:

Obtain permission from the receivers and retain all e-mail correspondence for the attention of the cargo surveyors.

Transfer no more than 5 % of the total cargo volume at any one time.

Obtain permission from the charterers and document all operations fully in the Oil Record Book.

It is not necessary to obtain any permissions, provided the Captain makes an entry in the Deck Log Book, documenting his reasons for moving cargo.

With reference to the exposure of “vapours” from oil cargoes, “Short Term Exposure Limit” value is determined by:

The airborne concentration of a toxic substance averaged over any 10 minute period, usually expressed in ppm.

The airborne concentration of a toxic substance averaged over any 15 minute period, usually expressed in ppm.

The airborne concentration of a toxic substance averaged over any 25 minute period, usually expressed in ppm.

The airborne concentration of a toxic substance averaged over any 30 minute period, usually expressed in ppm.

What is the relationship between absolute pressure and gauge pressure?

Absolute pressure = gauge pressure.

Absolute pressure = gauge pressure – atmospheric pressure.

I don’t know.

Absolute pressure = gauge pressure + barometric pressure.

As per MARPOL, the contents of lines and pumps on a crude oil tanker at completion of discharge must be:

Drained and then pumped either ashore, or to a cargo tank or slop tank on board.

That they be drained directly (and only) to shore.

That they be cleared to shore by the use of compressed air.

That agreement be reached at the pre-cargo conference as to whether the ship or shore facility are to receive the “unpumpable product remaining in lines and pumps” and the appropriate side then clear the lines to the other by any appropriate means.

DG placards shall be located on a freight container:

One on each end and one on each side.

One on each side (only).

One on each end (only).

One of the back end and one on one of the sides (only).

With reference to oil cargo calculations, API refers to:

American Petroleum Institute.

Approved Petroleum Inspector.

Average Petroleum Index.

Aggregate per Inch.

The compensation payment by the charterer that is due when a vessel is unable to load/discharge her cargo within the allowed and contracted time is referred to as:

Demurrage.

Contractual penalty discount.

Deferment.

Discretion.

As per the IMDG Code, “Marine Pollutant” is defined as:

A substance which is subject to the provisions of Chapter V of SOLAS 1974 as amended.

A substance which is subject to the provisions of Annex III of MARPOL.

I don’t know.

Any substance which is deemed hazardous to the marine environment.

What is to be considered when deciding the position of the accommodation on an oil tanker?

I don’t know.

A single failure of deck or bulkhead shall not allow fumes into the accommodation spaces.

They must be at the after end of the vessel.

There are no restrictions to the position of the accommodation.

If W = Displacement, L = length, B = Breadth, D = depth of vessel, Cb = Block Coefficient, Cw = Coefficient of Waterplane, RD = Relative Density, then:

W = L · B · D · Cb / RD.

W = L · B · D · Cb.

I don’t know.

W = L · B · d · Cw.

What is the purpose of girders in the tank?

They transfer all the cargo forces acting on the plating.

They support the stiffeners and also take up some of the sea forces.

They transfer all sea forces acting on plating.

They support the stiffeners.

Segregated Ballast Tanks on an oil tanker may best be defined as:

Cargo tanks which may be used for the carriage of ballast.

Cargo tanks which each have their own individual pumps, are fitted with independent piping systems and are served by unconnected ventilation arrangements.

Tanks which are completely separate from cargo or fuel oil systems, being permanently allocated to the carriage of ballast and fitted with their own pumps and associated piping.

Cargo tanks which may be used for ballast, where the lines are not connected to the Oil Discharge Monitoring Equipment.

Crude oils may be considered to consist:

A natural mixture of carbon and sulphur isomers.

A refined blend of hydrocarbon compounds and sulphur extracts.

A mixture of carbon extracts and naturally occurring wax.

A natural mixture of simple and complex hydrocarbon compounds.

Depending on the API, an error measurement of 0,1 degree Fahrenheit in a tank containing 300 000 barrels of oil will result in which of the following volumes?

50 barrels.

150 barrels.

300 barrels.

25 barrels.

When documenting Crude Oil Washing operations in the Oil Record Book, which of the following must be included in the sequence of entries?

The ullage in the tank at the commencement of washing.

The average oil cargo temperature during the washing operation.

The ship’s speed during the washing operation.

The method of establishing that the cargo tanks were dry.

With reference to ship stability, the letters “TPC” stand for:

Tonnes per Centimetre Immersion.

Tonnes per Centimetre.

Tipping Perimeter Centre.

Trim per Centimetre.

Which of the following type of crude oil requires special consideration in terms of carriage and cleaning?

Reconstituted Crude.

Medium Crude.

Paraffinic Crude.

Sweet Crude.

Why is it important to have good relationship on-board a vessel?

It encourages crew to extend their contract.

It will prevent accidents from happening.

It leads to better work performance and positive atmosphere among the crew.

Crew comes to know each others problems.

Where would you find the document relating to the “Condition of Freeboard Assignment” onboard?

With the Safety Construction Certificate.

With the Classification Records.

With the Loadline Certificate.

With the Structural Survey File.

What statutory certificate is carried onboard to indicate that a tanker is in compliance with Annex 1 of the MARPOL convention?

Oil Record Book.

The International Oil Pollution Prevention (IOPP) Certificate.

I don’t know.

International Safety Guide for Oil Tankers and Terminals (ISGOTT).

For security purposes, the IMDG Code should be read in conjunction with the:

Chapter XI-2 of SOLAS and Part A of the ISPS Code.

Part B of the ISPS Code and Chapter II of the Maritime Transport and Offshore Facilities Act.

I don’t know.

IMO NVIC 24 and 46 CFR 2.05.

Fluid driven eductors operate on Bernoulli’s principle, which states that:

The discharge rate is inversely proportional to the pressure applied in the drive inlet.

The increase in pressure at the eductor inlet is inversely proportional to the decrease in pressure as measured at the discharge orifice.

The speed of a moving fluid increases as the pressure in the fluid decreases.

The volume of a fluid increases as the pressure in it decreases.

The DoS addresses the responsibility for the security of the water around the ship and the verification of increased threat levels.

True.

False.

The ODME printed record for ballast water discharge overboard from the cargo piping system on oil tankers operations must be retained on board for a minimum period:

Of 3 years.

I don’t know.

Of 2 years.

Of 1 year.

During an audit, adherence to the company cargo handling procedures can best be demonstrated:

By requesting that an audit takes place during cargo operations.

By providing a summary of out-turn figures for the auditor.

I don’t know.

By being able to provide comprehensive and verifiable documentary records of cargo operations.

The purpose of the “mud box” fitted on a tanker is to:

Collect ships waste and water mud when ballasting and de-ballasting.

Catch the mud from the anchors and cables and deposit these at the windlass.

Restrict any particles and solids entering the pipeline system.

Catch spills when connecting the discharge or loading hose.

Prior to discharging cargo from an oil tanker, “line displacement” is usually conducted to:

To balance a rigid cargo arm.

I don’t know.

The calibration of the ship’s flow meter.

Verify the pipeline contents with previous grade have been replaced.

The examples of Aromatic Hydrocarbons will include:

Benzene, Toluene and Xylene.

Carbon Dioxide and Hydrogen Peroxide.

Propane, Butane and Pentane.

Hydrogen Sulphide and Carbon Monoxide.

The purpose of the decanting line between two slop tanks, where fitted, is:

To enable most of the recovered oil to be retained in the primary slop tank, while the cleaner part of the water will flow into the secondary slop tank, where it can be re-used as wash-water.

To avoid a build-up of static electricity during water washing, caused by air being drawn in as the primary slop tank empties.

To enable the filling of the secondary slop tank via the primary slop tank.

To enable both the primary and secondary slop tank to be filled without using the main cargo lines.

Which of the following best describes what the wax content of crude oil is?

The percentage of wax, expressed as a percentage, remaining in an oil product after distillation.

The percentage, by weight, of paraffinic wax found in a representative sample of the crude oil.

I don’t know.

The observed volume percentage of waxy deposit found in a cargo tank after discharge in relation to the total volume of cargo previously carried.

As per MARPOL, the formula for calculating the minimum draft amidships for crude tankers in ballast condition is:

2,0 + 0,02 L.

I don’t know.

2,0 + 0,015 L.

2,0 + 0,002 L.

What is the purpose of girders in the tank?

They support the stiffeners.

They transfer all sea forces acting on the plating.

They transfer all the cargo forces acting on the plating.

They support the stiffeners and also take up some of the sea forces.

To correctly report an oil spill in US waters:

The master of the vessel responsible for the spill must advise the Environmental Protection Agency National Incident Reporting Center (or the appropriate regional office) within 2 hours of the incident being reported to that person.

The person in charge must first report the spill to the National Response Center or, if not practicable, to the Environmental Protection Agency regional office or local US Coast Guard Marine Safety Office. This must be done immediately that person has knowledge of the spill.

The person responsible for the spill must report preliminary details to the appropriate State Police within 30 minutes of the accidental discharge taking place.

I don’t know.

When an inhibitor is added to an oil cargo, the items mentioned on the accompanying certificate include:

Inhibitor name; amount added; date added; period of efficiency; precautions if voyage length exceeds that period; eventual temperature limitation.

Inhibitor class; amount added; date of expiry; minimum period of optimum efficiency; precautions to be taken when added; minimum temperature requirement.

Inhibitor name; percentage applied; date of expiry; precautions to be taken on voyage and interval of application; maximum temperature at which continuously effective.

Inhibitor class; percentage blended; date added; maximum period of efficiency and applicable temperature limits; maximum storage period on board; contact number of manufacturer.

How much liferaft capacity should be provided on a conventional cargo ship of more than 85 metres in length?

25 % of the complement on each side of the ship.

100 % of the complement if it can be readily launched on either side of the ship. If it cannot be readily launched on either side, 100 % must be provided on each side.

75 % of the complement on each side of the ship.

50 % of the complement on each side of the ship.

Oil tankers are subject to cyclical bending moments throughout their life as a result classification society rules require a specific minimum reduction in steel thickness to be maintained within “x” length amidships, where “x” is:

0,4 length.

I don’t know.

0,2 length.

0,3 length.

The chemical characteristics of effluent water from an inert gas scrubber and the condensate which collects in the deck mains would be:

Acidic in nature.

Demineralised in nature.

Alkaline in nature.

Neutral in nature.

A tanker in ballast, having recently left the discharge port is involved in a collision. The two vessels are still interlocked after the collision and a survey of the ships gives all crew members are safe and the damage is focussed to the vicinity of the impact. What should be the greatest concern at this time?

When the two vessels separate one (or both) of the vessels will have insufficient stability to remain afloat.

The vessels moving together will create even greater damage to their structures.

The possibility of pollution.

The ships moving together in the swell/seaway will cause a spark and consequently an explosion.

An oil tanker with a defective Oil Discharge Monitoring Equipment may be allowed by a Port State Authority to trade for:

One ballast voyage before proceeding to a repair port.

I don’t know.

The vessel will be detained until ODME is rectified.

Two ballast voyage before proceeding to a repair port.

The scantling draft of an oil tanker fitted with segregated ballast tanks is:

The minimum draught amidships when in ballast condition.

The maximum draught determined by the Loadline Rules.

The draught for which the structural strength of the ship has been designed.

I don’t know.

As per IMDG Code, the term “separated from” can be defined as:

I don’t know.

Either in a vertical or horizontal separation: if the intervening decks are not resistant to fire and liquid, then only in a longitudinal separation is acceptable. For “on deck” stowage, this means a distance of at least 12 metres. This distance also applies to one package stowed “on deck” and another in an upper compartment.

In different compartments or holds when stowed “under deck”. Provided an intervening deck is resistant to fire and liquid, a vertical separation may be accepted as equivalent. For “on deck” stowage, this segregation means a distance of at least 6 metres.

With an intervening compartment, being both a vertical and horizontal separation. Provided an intervening deck is resistant to liquid and fire, a vertical separation of 6 metres is acceptable. For “on deck” stowage, this segregation means a distance of at least 12 metres irrespective of compartment divisions.

The longitudinal bending moments caused by cargo distribution on an oil tanker need to be taken into consideration:

Only during loading and discharging cargo.

Only when on ballast passage in heavy seas and when the vessel is pitching.

Only when on loaded passage in heavy seas and when the vessel is pitching.

During loading, discharging and on loaded passage.

When in-service testing a hose used for cargo transfer on an oil tanker (and for which the elongation of the hose assembly when new was greater than 2,5 %), the maximum permitted elongation before the hose must be withdrawn from service should be:

I don’t know.

Not more than 1,5 times the temporary elongation measured at the previous in-service test, as documented in the ship’s annual test record.

Not more than 1,5 times the temporary elongation measured when the hose assembly was new, as documented in the manufacturer’s certificate.

Not more than 1,25 times the temporary elongation measured when the hose assembly was last tested, as documented in the appropriate certificate.

When describing the characteristics of oil cargoes or oil/water slops, a “mercaptan” is:

A device fitted to a cargo pump which automatically alerts the operator once traces of water start to be detected during discharge.

A chemical additive blended with crude oil to inhibit the natural “rotten egg” smell associated with certain grades.

The component of hydrocarbon-based cargoes which is formed from Merolion Carbonized Tannin.

A colourless, odorous gas, with a smell similar to rotting cabbage and which is generated naturally by the degredation of natural organisms, as may be found where water has remained under oil for a long time.

When conducting a risk assessment for a shipboard work activity, the two elements to be considered are:

The chance of an incident re-occuring and the potential effects of an loss.

The available manpower and their experience in this type of work.

The potential severity of harm and the likelihood that harm will occur.

I don’t know.

Substances, materials and articles shall be stowed as indicated in the Dangerous Goods List of the IMDG Code, in accordance with a series of stowage categories, which are designated as:

5 categories, labelled A-E.

Three categories, numbered I, II and III.

10 categories, lattered A-K (excluding I).

10 categories, numbered 1-10.

What are the three volumes of the IAMSAR Manual?

A – Command and Control; B – Communications; C – Rescue Procedures.

I – Planning and Preparation; II – Rescue Control; III – Reference.

I – Organization; II – Communications; III – Rescue Procedures.

I – Organization and Management; II – Mission Co-ordination; III – Mobile Facilities.

According to 33 CFR 156.170, for oil tankers trading in US waters, the minimum requirement for testing of cargo transfer hoses and associated piping system are:

That no leakage occurs under dynamic fluid pressure of less than 1,5 times the maximum allowable working pressure.

That no leakage occurs at the nominal anticipated working pressure.

That no leakage occurs under static liquid pressure of at least 1,5 times the maximum allowable working pressure.

I don’t know.

“Door to door” shipment is covered under:

A Multi-Phase Bill of Lading.

A Through Bill of Lading.

A Destination Bill of Lading.

An Ocean Bill of Lading.

When discharging dirty ballast from an oil tanker at a high flow rate with main cargo pumps, the instantaneous rate of discharge of oil is calculated by formula:

Instantaneous rate of discharge (l/nm) = oil content (ppm) · flow rate (m3/h) / speed (knots) · 1 000.

Instantaneous rate of discharge (l/nm) = oil content (ppm) · 1 000 / flow rate (l/h) · speed (knots).

Instantaneous rate of discharge (ml/nm) = oil content (ml/nm) · flow rate (l/m) / speed (knots) · 100.

I don’t know.

The approximate Upper Flammable Limit of Crude Oil when measured as a percentage volume in air is:

12,6 %.

15 %.

2,2 %.

9,5 %.

During Crude Oil Washing, those areas of the cargo tanks which are not directly struck by the oil jet from the tank washing machines are referred to as:

Hidden areas.

Protected areas.

Deflected areas.

Shadow areas.

The maximum oxygen content by volume permitted in the cargo tanks throughout the crude oil washing operation is:

10 %.

5 %.

3 %.

8 %.

If the shipper wishes to ensure that a vessel or her operators will not be held responsible for any damage that may arise from the carrier issuing a clean Bill of Lading, even though the Mate’s receipt is marked as “unclean”, such a document is called the:

An addendum to the Bill of Lading.

A Letter of Credit.

I don’t know.

A Letter of Indemnity.

Prior carrying out a Crude Oil Washing operation, the tank from which the crude is to be used for washing is usually partially discharged. This is done so as to:

Ensure that all water settled in the tank is removed prior washing, so as to ensure that the fresh cargo can be loaded on top without fear of contamination.

Ensure that only the required quantity of oil are kept in the tank, so as to reduce the amount of slops retained on the ship.

Ensure that any settled water is removed from the tank and only “dry” crude is used for washing so as to avoid electrostatic hazards during washing.

As per the IMDG Code, an “article” is referred to as:

Something that is packed within a freight container.

A device that is responsible for initial dangerous reaction.

A device that contains a dangerous substance or mixture of substances.

A form that contains important information about a hazardous substance.

When cargo discharge reaches stripping levels on an oil tanker, it is necessary to reduce the inert gas pressure so as to:

Comply with the requirement of MARPOL Annex VI.

Avoid over-capacity in the IG generator.

Avoid locking the cargo pump impeller.

Minimise blowback.

Ship’s cargo pump room alarm must be automatically activated when levels of hydrocarbon gas concentration are:

No higher than 10 % of LEL.

No higher than 5 % of LEL.

No higher than 15 % of LEL.

I don’t know.

A VLCC is to anchor in a depth of 80 meters in open water with moderate swell running. How many shackles of anchor chain should be used to ensure safely anchored?

8 shackles.

11 shackles.

6 shackles.

3 shackles.

As per the US Code of Federal Regulations, the current Oil Transfer Procedures for a vessel carrying out discharge in US ports must be:

That the procedures be legibly printed in a language or languages easily understood by personnel engaged in the transfer operation and permanently posted or available at a place where crew members can see and use them.

That the Master of the vessel engaged in a transfer shall, before commencing any transfer operation, ensure that all crew members involved in that operation shall be familiar with the applicable operating and emergency procedures and be capable of communicating in a common language with terminal operators.

That the procedures be available in hard-copy or electronic format to the Supervising Officer in a language with which he is familiar.

That the procedures be printed in the English and Spanish languages and permanently posted in the wheelhouse of the vessel.

The purpose of expansion couplings to be fitted on the longitudinal pipelines of oil tankers is:

To allow the pipelines to follow the ships flexing movement when pitching.

To allow the pipeline to expand when loading a hot cargo through the pipeline.

To prevent the pipeline from cracking when the ship suffers from Racking stresses.

I don’t know.

What is the ideal maximum viscosity at which crude oil cargoes are best discharged for maximum efficiency of centrifugal pumps:

450 cSt (450 mm2/s).

I don’t know.

250 cSt (250 mm2/s).

45 cSt (45 mm2/s).

Master of every ship must provide:

Facilities to conduct training whenever required by the training officer.

A link between the shipboard training officer and the company training officer ashore.

The training during crews working hours only.

Proper rest to the crew after each training programme.

The compensation payment by the charterer that is due when a vessel is unable to load/discharge her cargo within the allowed and contracted time is referred to as:

Contractual penalty discount.

Discretion.

Demurrage.

Deferment.

The approximate API gravity of Arabian Light Crude is:

30°.

40°.

27°.

33°.

On oil tankers, Cargo tanks can be isolated from machinery spaces by:

All the answers are good.

Pump room.

Cofferdams.

Ballast tanks.

Special Areas as per MARPOL are:

Specific geographical sea areas in which special mandatory measures for the prevention of sea pollution by oil are required.

Specific geographical sea areas, designated as Marine Conservation Areas by the United Nations, in which any discharge from the cargo area of an oil tanker is strictly controlled.

All sea areas within 50 miles from the nearest land, where that coastal state is a signatory to MARPOL.

Limited ocean and sea areas, listed under the OPA-90 Act, inside which the discharge of oil is prohibited and the penalty for doing so is an unlimited fine and jail sentence.

Oil tankers built and delivered after 6th July 1986 may have wing ballast tanks that extend throughout the cargo tank length. In this case the design feature against pollution in the event of the bottom being breached is that:

Additional level sensors and alarms must be fitted to give early warning of oil outflow.

Steel thickness in the bottom area must be a minimum of 1,36 times that otherwise required by construction regulations to minimise the extent of any breach.

The cargo tank levels must be set so that hydrostatic pressure will stop oil outflow.

The pressure vacuum valves must be capable of complete sealing, and the integral strength of the tank such that a total vacuum is capable of being maintained in the breached compartment, thereby preventing outflow of oil.

One particular group of hazardous goods that is highlighted by the IMDG Code as potentially being the most dangerous for carriage is:

Infectious substances.

Organic peroxides.

I don’t know.

Liquefied gases.

You are on a sailing vessel, underway in open water. This vessel is sighted on the starboard bow, on a steady bearing and the distance is closing. By the International Regulations for the Preventing Collisions at Sea, what action will you follow?

Risk of collision is deemed to exist and, as the other vessel is on a steady bearing on my starboard side, I will maintain my course and speed.

This vessel is clearly a power-driven vessel and I anticipate that the bearing will therefore close and she will pass ahead at a safe distance.

Risk of collision is deemed to exist and, as the other vessel is on a steady bearing on my starboard side, I am required to keep out of the way. I will make a broad alteration of course to starboard.

By Rule 18, a power-driven vessel underway shall keep out of the way of a sailing vessel. I will maintain my course and speed, but will continue to monitor situation to ensure the other vessel takes avoiding action.

For a vessel proceeding enroute, located more than 50 nm from nearest land outside a special area and having in operation its ODME, the maximum instantaneous rate of an oily water mixture is:

30 litres per nautical mile.

300 litres per nautical mile.

60 litres per nautical mile.

I don’t know.

If all indications are that a cargo has been received without damages, irregularities or short shipment and the phrase “apparent good order and condition” is entered on the Bill of Lading, then this Bill is this said to be:

A Due Title Bill of Lading.

An endorsed Bill of Lading.

A Bill of Lading completed for shipment.

A clean Bill of Lading.

The maximum permitted oxygen content in the inert gas supply when inerting a cargo oil tank prior to gas freeing is:

8 % by volume.

12 % by volume.

5 % by volume.

I don’t know.

As per international regulations, the minimum inert gas pressure required to be maintained in slop tanks if slops are retained on board is:

10 mm/water gauge.

750 mm/water gauge.

1 000 mm/water gauge.

100 mm/water gauge.

The purpose of permanent continuous coamings fitted from side to side across the decks near the accommodation of an oil tanker is:

To keep deck spills away from the accommodation and service areas.

To reduce the effects of racking stresses.

To push the sea water shipped onto the deck over the sides of the ship.

To increase the strength of the deck structure.

As per the IMDG Code, “Proper Shipping Name” is defined as:

The correct chemical name of a potentially hazardous material, as identified from the Chemical Cargo List.

The name under which a dangerous material, substance or article is described for export purposes in the country of loading.

The name assigned by the manufacturer to a material, substance or article for the purposes of shipment.

The name to be used in any documentation relating to the transportation of the dangerous substance, material or article, such as on forms, labels and placards.

What is meant be the term “sour crude”?

Crude oil containing hydrogen sulphide content greater than 0,1 % by volume.

Crude oil containing hydrogen sulphide content greater than 0,3 % by volume.

Crude oil containing hydrogen sulphide content greater than 0,5 % by volume.

I don’t know.

The «Cargo Handling and Stowage, Management, Oil Tanker» subject provides both theoretical and practical knowledge on safely working with electrical equipment. Mastery of this material is a key indicator of an employee’s competence in their role aboard a vessel. Cargo handling and stowage on an oil tanker involve the processes of loading, unloading, and storing liquid cargo, such as crude oil or petroleum products. These operations require meticulous planning, strict adherence to safety protocols, and compliance with industry regulations to ensure the safe and efficient transportation of liquid cargo.

Version: 4.1, 5.0, 5.1, 6.0.0, 6.0.8, 6.0.10.
Test type: STCW.
Department: Cargo Handling and Stowage.
Level: Management.
Vessel type: Oil Tanker.

Seuls les marins peuvent laisser des avis. Pour laisser un avis, connectez-vous au site en utilisant votre compte marin.

Soyez le premier à évaluer ce test en ligne !