Тест складається із 80 випадкових питань.
Усього питань на цю тему: 95
Which of the following is the correct minimum carriage requirement for a ship of more than 300 gross tons and operating in area A1:
1 VHF RT + DSC + DSC watch receiver – 1 or 2 SART – 1 NAVTEX or 1 EGC receiver- 2 or 3 VHF portable – 1 EPIRB.
1 VHF RT + DSC + DSC watch receiver – 1 or 2 SART – 1 NAVTEX or 1 EGC receiver – 2 or 3 VHF portable.
A SART is used by a vessel in distress. This SART is seen on the screen of a:
What immediate action should be taken if a ship unexpectedly runs aground and stops?
On area A4 the function “Transmission and reception of signals for locating” is mainly based on:
The use of SARSAT COSPAS Epirbs.
The use of SART transponders.
What is usually the effect on G when the ship is damaged with water ingress?
It first rises and then lowers.
Which option best describes the purpose of having an FMEA completed for a DP vessel?
Because the crew will not investigate failure themselves.
So that when failure occurs, the vessel position is maintained.
On a platform supply vessel, how are the risks associated with the dry bulk system controlled?
By requiring crew to always follow operating procedures.
By first opening the deck valve,then the tank valve.
A rocket parachute flare reaches an altitude of:
Non distress calls on 2 182 kHz and VHF channel 16 should not exceed:
If W = Displacement, L = length, B = Breadth, D = depth of vessel, Cb = Block Coefficient, Cw = Coefficient of Waterplane, RD = Relative Density, then:
A satellite receives the transmissions of the 406 MHz Cospas-Sarsat EPIRB. The transmissions of the EPIRB will be:
Always passed on to a LUT.
Exclusively passed on to a LUT only between 70 degrees N and 70 degrees S.
Exclusively passed on to a LUT if the satellite sees both the EPIRB and the LUT.
Where on a vessel moving ahead through the water, is the most dangerous place for a tug to manoeuvre?
The most dangerous position is where the tug approaches the bow, rounding the shoulder to pass a line.
The most dangerous position is where the tug approaches the stern of the larger vessel and enters into its associated positive pressure field.
With help of DSC a ship wants to contact a coast-station to have a question for telephone call. One has to choose from the following DSC-frequencies:
TX: 8 415,0 kHz. RX: 8 415,5 kHz.
TX: 8 436,5 kHz. RX: 8 436,5 kHz.
TX: 8 415,0 kHz. RX: 8 436,5 kHz.
Which option correctly completes the following statement? A failure modes and effects analysis (FMEA) is:
A practical assessment of failure.
A deductive prediction of failure.
The receipt of a distress alert is to be pronounced as followed:
Mayday (1x), call-sign of ship in distress (3x), I this is I, own call-sign (3x), I received mayday.
Mayday (3x) I this is I, own call-sign (1x), I received mayday, I call-sign of ship indistress (1x).
Which of the following is a Accounting Authority Identification Code?
The bridge wheelman has not reported for duty and there is a suspected “Man Overboard” situation on your vessel. The ship has been searched and there is one seaman missing? The vessel turns round and retraces the course back,calling for assistance from other vessels in the vicinity What should be the focal point for any search pattern to be established?
Determine the drift and leeway of own ship and take this deviation from track into account on the return course. The search should focus around this return track back to the last sighted position.
Determine when the seaman was last sighted and concentrate the search round the course line between the last sighting and present position, taking into account any prevailing current.
For the same vessel and the same rudder angle, is the diameter of the turning circle completed at full ahead smaller than one completed at half ahead?
No, the diameter of the turning circle would be almost the same.
Yes, it will be much larger turning circle at half ahead.
Yes, there would be a change of shape of the turning circle; it would have an increase in the transfer, but not the advance.
Yes, it would be a much smaller turning circle at half ahead.
Which PPM is allowed for discharging of “Bilge Water” overboard?
How can an ARPA best assist the bridge team to steer a suitable course to make good the entrance to a channel?
Alter course so that own-ships ground stabilised true vector passes through the entrance to the channel.
Acquire a buoy at the entrance to the channel and alter course to make the relative vector of the buoy point at own-ship.
What is the purpose of having an FMEA proving trial undertaken on a DP vessel?
To confirm the predictions in the FMEA report.
To see how well the vessel can hold position.
What is the main purpose of an offshore vessel inspection using CMID? Select the ONE best answer.
To confirm that a vessel is fit for purpose.
To satisfy elements of the ISM Code.
Select the ONE answer which completes the following statement correctly. High priority safety findings during an OVID inspection:
Need to be addressed immediately by onboard staff.
Have to be passed on to the company owning or managing a vessel.
Who should undertake a CMID pre-inspection check? Select the ONE best answer.
The management team on a vessel.
A specialised inspection company.
A vessel has been in involved in a collision. Which procedure should happen immediately?
There is assessment of the damage stability.
Determine any injuries of persons on board.
As a result of being in collision with your vessel, the other vessel involved is on fire? What are your responsibilities to it?
The target is on a constant bearing and getting closer to own ship.
The target is on the same course and speed as own ship.
When on HF band a DSC distress alert is received, you have to listen to:
The radio telephony distress frequency in the band in which the DSC distress alert was received.
8 414,5 kHz (DSC distress frequency in 8 MHz).
If one wishes to make a collect call from a vessel to a shore subscriber, one must:
Request for a personal call.
Request for telephone message stating name, address and telephone number.
Request for a collect call.
On area A4 the function “Transmission of ship to shore distress alerts” is mainly based on:
The use of HF DSC and INMARSAT Epirbs.
The use of HF DSC and COSPAS SARSAT Epirbs.
The use of MF DSC and INMARSAT Epirbs.
The use of VHF DSC and VHF Epirbs.
A battery of 24 Volt supplies during 10 hours a current of 6 ampere. What is the capacity supplied:
What action should be taken by the Officer of the Watch if someone reports a fire to them?
Send the bridge look-out down to investigate.
Stop engines and inform the engine room.
The steps of the embarkation ladder used must be proportioned as it follows:
Length = 480 mm, breadth = 115 mm, depth = 25 mm.
Length = 580 mm, breadth = 165 mm, depth = 30 mm.
Length = 280 mm, breadth = 85 mm, depth = 10 mm.
Length = 380 mm, breadth = 145 mm, depth = 20 mm.
Which option best completes the following statement? The version of the IHO presentation library on the ECDIS is important because…
If it is not the latest version, the ECDIS will not be compliant.
It is where the files for maintenance of the system software are stored.
Which of the following requirements regarding on board stability data corresponds to present regulations? (NSCL 4/12.1).
A calculation example showing the use of “KG” limitation curves.
A calculation example showing use of “GM” limitation curves.
Stability data produced by stable calculation instruments.
Drawings and calculations documenting the stability of the ship, both in intact and all possible damage condition.
By the degree of selectivity of a receiver is meant:
Ability to prevent variations in the strength of radio frequency signal received.
Ability to make weak stations audible.
Ability to distinguish weak stations from adjacent stronger stations.
What is meant by the “level” of system failure on a DP vessel?
It is failure of either a component, a supporting piece of equipment or the entire system.
It is a measure of how far a single failure will affect the position keeping ability of a vessel.
Why should an offshore vessel inspection be based on the CMID? Select the ONE best answer.
To ensure that the inspection is the same for all similar vessels.
To ensure that the inspection is done every 5 years.
On-board training in the use of davit-launched liferafts (including inflation and lowering whenever practicable) must take place:
The prescribed test of an approved portable VHF radio set (portophone) must be done once a:
A tug is connected to the bow of a vessel. Will the force exerted by it be the same at any ahead speed?
No, on the bow the tug uses power to run with the vessel, which reduces the available power on the towline.
No, when the ahead speed of the ship increases the force exerted by the tug will also increase.
Who is responsible for ensuring your ship completes a security assessment?
Flag State Administration.
Company Security Officer.
The Ship Security Officer.
The Port Facility Security Officer.
Whether or not the NAVTEX is functioning properly, can be checked using:
A compulsory built-in alarm for defects.
A testing program built in for this purpose.
Your vessel is in restricted visibility and you hear this signal. What type of vessel does it come from and what additional information does the signal provide?
A vessel aground, more than 100 metres in length. The additional signal indicates which side the clear water lies on.
A vessel at anchor, less than 100 metres in length. She is sounding the additional signal top give warning of her position.
A vessel at anchor, more than 100 metres in length. The additional signal indicates that her cable extends at least 25 metres from her bow.
A vessel at anchor, more than 100 metres in length. She is sounding the additional signal to give warning of her position.
Which organization or administration is responsible for surveys and inspections of ships, and the issue of Safety Certificates?
Government Authorities of the Flag State.
Ships Classification Associations (Lloyd’s, American Bureau of Shipping, The Norwegian Veritas, Germanische Lloyd’s, etc).
International Labor Organisation (ILO).
International Maritime Organisation (IMO).
During the survey of Long Range Identification and Tracking (LRIT) equipment, which document must be available to the surveyor to demonstrate compliance with SOLAS?
A report giving the result of the Conformance Test issued by an Application Service Provider on behalf of an Administration.
A report giving the result of the Performance Test, issued by the manufacturer in compliance with the Flag State Authority requirements.
The Certificate of Compliance with SOLAS V/19-1, bearing the serial number of the equipment installation.
A Statement of Installation and Testing by the Approved Service Provided in compliance with SOLAS V/26-4.
Which class of emission is used for VHF DSC transmissions?
What is the correct setting of the “Anti sea clutter” control on the radar?
A few sea returns remaining around the own-ship position.
All of the suggested answers.
No sea returns left on the screen which may confuse with small target echoes near the ship.
A removal of all the sea returns down to about a mile from own ship.
When using an ENC chart to passage planning, why should a scale at or near its compilation scale always be used?
The chart detail is correct for its usage band.
That is incorrect, as any ENC can be zoomed in or out for passage planning.
By FleetNET communication is understood:
An EGG-message destined for ships with the same group call number.
A HF-NBDP-message destined for ships in a certain geographical area.
A MSI-message destined for ships in a specific geographical area.
On area A3 the function “Transmission and reception of on scene communications” is mainly based on:
The use of HF/MF and/or VHF R/T and/or INMARSAT-C.
The use of MF and/or HF R/T.
The use of SART transponder.
Which one of the listed requirements regarding life-saving appliances corresponds to present regulations?
All prescribed life-saving appliances shall be made of non-combustible or fire retardant material.
All prescribed life-saving appliances shall be of such a colour that they are in contrast to the surrounding colour.
All prescribed life-saving appliances shall be of a highly visible colour on parts where this will assist detection.
All prescribed life-saving appliances shall be resistant to deterioration where exposed to sunlight.
As per the IMDG Code, “Proper Shipping Name” is defined as:
The correct chemical name of a potentially hazardous material, as identified from the Chemical Cargo List.
The name to be used in any documentation relating to the transportation of the dangerous substance, material or article, such as on forms, labels and placards.
Which one of the listed requirements regarding the stowage of a survival craft corresponds to present SOLAS regulations? Each survival craft shall be stowed:
In a state of readiness so that two crew-members can prepare for embarkation and launching in less than 15 minutes.
Wherever space is available.
On the starboard side of the ship.
In a secure and sheltered position and protected from damage by fire or explosion.
During the survey of Long Range Identification and Tracking (LRIT) equipment, which document must be available to the surveyor to demonstrate compliance with SOLAS?
A report giving the result of the Conformance Test issued by an Application Service Provider on behalf of an Administration.
The Certificate of Compliance with SOLAS V/19-1, bearing the serial number of the equipment installation.
What is SITREP an abbreviation for:
Ship Transit Emergency Radio.
Survivor Indication Transponder Equipment.
Ship Indication Transmission Equipment.
Which option best describes the purpose of having an FMEA completed for a DP vessel?
So that annual trials can take place.
So that when failure occurs, the vessel position is maintained.
If proving trials show that the FMEA report is incorrect for a DP vessel, what action should be taken?
The FMEA should be changed to reflect reality.
The trial should be stopped immediately.
Which of the following two digits codes is used to obtain maritime assistance?
Which of the following requirements regarding life-buoys correspond to present regulations? (SOLAS III/7.1).
Not less than half the total number of lifebuoys shall be provided with self-ignighting lights.
At least four life-buoys on each side of the ship shall be fitted with buoyant lifelines.
All the life-buoys shall be placed in holders with quick-release arrangement.
At least one lifebuoy with self-activating smoke shall be placed within the vicinity of the stern.
The offshore vessel inspection database (OVID) used for offshore vessel inspection reports is hosted by which organisation? Select the ONE correct answer.
The Oil Companies International Marine Forum.
The Marine Contractors International Association.
If during a DP vessel design, the FMEA predicts a possible catastrophic effect with a system failure, what will happen?
The design will be changed to remove the catastrophic event.
The effect will be logged for future operator information.
On a platform supply vessel, what should happen with dangerous cargo?
It should be manifested and in a marked container.
It should always be stowed together with all other dangerous cargo.
A member of the bridge team has just seen a person fall overboard. Which of the following manoeuvres is the most appropriate to assist with a rescue?
As a result of being in collision with your vessel, the other vessel involved is on fire? What are your responsibilities to it?
The other vessel is in distress and if possible I will render assistance.
There is no statutory requirement to provide assistance as the actions of that vessel were the primary cause of the collision.
A “Standard Format for Search and Rescue Situation Reports” (SITREPs) should be used by vessels in distress. The SITREP can be compiled as a short form (urgent essential details). Which of the following information shall be included when using the “short form”?
As per the IMDG Code, “Marine Pollutant” is defined as:
A substance which is subject to the provisions of Annex III of MARPOL.
A substance which is subject to the provisions of Chapter V of SOLAS 1974, as amended.
Any substance which is deemed hazardous to the marine environment.
A substance which, because of its tendency to degrade in seafood, or because of its hazard potential to the aquatic environment is subject to the provisions of Annex I of MARPOL 73/78, as amended, and carried by sea accordingly.
In area A1 the function “Reception of shore to ship distress alerts” is mainly based on”:
The use of SART transponders.
The use of SARSAT COSPAS Epirbs.
In a distress situation and immediately after the distress signal has been sounded, what is the next action to be taken by the Chief Officer on duty?
Use the intercom to inform crew and passengers of the reason for the alarm.
Send distress signal to call for help.
Use the VHF radio telephone to ask ships in the vicinity to stand by.
Call the nearest coast radio station.
If for some reason a vessel does not comply with a Classification Society’s requirements, what can a surveyor issue to the vessel enabling it to sail to the next port or for a period of time?
A Notification of Deficiency.
A revised Class Notation.
A Notification of Detention.
If the shipper wishes to ensure that a vessel or her operators will not be held responsible for any damage that may arise from the carrier issuing a clean Bill of Lading,even though the Mate’s receipt is marked as “unclean”, such a document is called the:
An addendum to the Bill of Lading.
An absolution clause in the shipping documents.
Onboard the following message is received on the DSC controller: DOO: 245329000 CH16; S distress ack 244123000. What station sent the distress acknowledgement?
For calling a coast-station by VHF one should preferably use:
A working channel of the nearest shore-station of that coast-station.
A special calling channel of that coast-station.
Under what convention is the master to ensure that a ship is seaworthy and in a fit state to safely carry a shipper’s cargo?
Which of the following duties shall be included in the “muster list” as being assigned to crewmembers in relation to passengers?
Assembling passengers at muster station.
Ensuring that every passenger is provided with an immersion suit or air thermal protective aid.
Clearing the escape routines.
Ensuring that extra food and water is taken to the survival craft.
Which organisation verifies the computational results and stored ship data used by the stability program loaded on a vessel’s computer?
The Classification Society.
Which organisation produces the Common Marine Inspection Document used for offshore vessel inspection? Select ONE answer.
The International Marine Contractors Association.
The International Maritime Organisation.
In open water, you see a collision between two other ships. What immediate action should you take?
Contact one or both vessels involved in the incident and offer assistance.
Nothing, proceed on passage unless they are in distress.
For how long time should a VHF survival craft transceiver be able to operate on its batteries?
Where several rescue units are engaged in a search and rescue operation, one of them may be designated as the On-Scene Coordinator (OSC) Which of the following describes how this appointment will be made?
The coastguard will appoint the OSC using their vessel database to assess suitability.
The OSC will always be designated by the Search and Rescue Mission Coordinator.
Which document should to be completed before an OVID inspection? Select the ONE correct answer.
The Offshore Vessel Particulars Questionnaire.
The Offshore Vessel Inspection Database.