Le test comprend 80 questions aléatoires.
Total de questions sur ce sujet : 95
What is the inherent danger in welding/cutting in piping containing freon?
Development of nitrous gases.
Depletion of the ozone layer.
Depletion of oxygen in the air.
Development of explosive gases.
What kind of safety clothing should be worn during a mooring operation?
Helmet, safety shoes, gloves and protective clothes.
Safety shoes and boiler suit.
No particular safety clothes are required.
In the figure, which arrow indicates the direction “ASTERN”?
Astern is indicated by D.
Astern is indicated by B.
Astern is indicated by A.
Astern is indicated by C.
What is the correct understanding of the term “gangway”?
Portable bridge arrangement between ship and shore, when alongside.
The ladder arrangement to allow walking access down the ship’s side into a boat alongside the vessel.
The access arrangements on an oil tanker between the bow and the after accommodation.
What is the minimum capacity of the portable tank of a portable foam applicator?
One of the checks during the annual Class survey of the UMS functions is focusing on cleanliness of the engine room. What is the reason for such a check?
To reduce the general risk of fire in an unmanned engine room.
To avoid frequent alarms.
To have the engine room looking tidy.
To prevent risk of pollution.
One of the categories of information that must be included in your SSP is:
Weaknesses in security measures.
On the figure there are four (4) possible definitions of the term “BOLLARD” given. Which one is the correct one?
Bollard is given by C on the figure.
Bollard is given by D on the figure.
Bollard is given by B on the figure.
Bollard is given by A on the figure.
When a ship is steaming along a course line, what is the importance of determining the set and rate of drift due to wind and current?
All of the suggested answers.
To appreciate the possible extent of drift and dangers in the event of engine failure.
To determine the time required to reach the next alteration of course point.
To determine the correction required to the course steered to maintain the planned passage.
Which of these conventions is The International Ship and Port Facility Security (ISPS) Code a part of?
The Anti Terrorist International Agreement.
What percentage of the baggage is required to be checked at Security Level 1?
The percentage is not specified.
5-15 % of the baggage is required to be checked at Security Level 1.
25-50 % of the baggage is required to be checked at Security Level 1.
100 % of the baggage is required to be checked at Security Level 1.
In which one of the following an oil, the flash point of which only needs to be over 43 °C, may be used?
Which Security Levels requires the highest security alert?
On the figure there are four (4) possible directions shown by the arrowed lines. Which one would correctly shows the direction understood by the term “AFTER SPRING”?
After spring is defined as B.
After spring is defined as C.
After spring is defined as D.
After spring is defined as A.
Where may as a general rule pressure containers for gas fire-extinguishing medium be kept? SOLAS II-2/5.1.10.
Outside the space which is to be protected.
In the space which is to be protected.
With an Inmarsat-C installation there is the addressing-option “special”. Via this option:
Give one of Inmarsat’s “special access codes”.
You can send a message by express delivery.
You can deliver a message via a special telegram.
Who is responsible for ensuring your ship completes a security assessment?
Company Security Officer.
Flag State Administration.
Recognized Security Organization.
Why should Ground Stabilised True Motion display mode be avoided when using the ARPA for anti-collision purposes?
The collision regulations are based on ship courses through the water.
The Relative Motion display and relative vectors is the only display to use for anti-collision purposes.
The true vector can never give an indication of collision risk with another ship.
True motion does not provide the collision risk of other ships.
Which of these procedures should crew follow when conducting a bomb search?
Stand quietly in various spots around the space, listening for unusual sounds like the tick tock of a clock mechanism.
Wait in the area they’ve finished searching until they’re contacted for a status update.
Conduct random or spot checks of logical threat areas.
Search the perimeter of the space up to a height of 5 feet.
“Overshoot” is an expression related to a ship’s steering ability. What is the correct understanding of this expression?
It is how many degrees of the compass a ship continues to turn after applying counter-rudder.
It is the way a ship turns when putting the helm in a hard over position.
It is the amount a ship moves forward after the engines are stopped.
It is the way a ship continues to turn when the helm is pup amidships.
Which statement about IED’s is true?
All IED’s have four common components.
IED’s don’t cause serious damage.
IED’s are difficult to manufacture.
If circumstances permit, how should low expansion foam be applied to oil burning near a bulkhead of the engine room?
The foam should be aimed at the bulkhead behind the fire and allowed to spread out slowly over the fire.
The applicator should be used in a sweeping motion to spread the foam over the surface.
The foam should be applied to the centre of the fire.
The foam should be aimed at about 45° upwards so that it can drop onto the fire.
On a fire patrol at night you see smoke coming from a closed cabin door. What action should you take first?
Activate the nearest fire alarm button and advise bridge of the location of the fire.
Take a look inside the cabin to see what the situation is.
Get the nearest fire extinguisher and then open the door to see what the situation is.
As most people are sleeping, call a friend and ask him to assist in putting out the fire.
What is the purpose of the Ship Security Plan?
Protect your ship from risks posed by security threats or incidents.
Outline specific measures for your ship to move from security level 1 to 2 and from 2 to 3.
Detail the duties of shipboard personnel assigned security responsibilities.
Outline the organizational structure for the ship.
What do crew, visitors and contractors all have in common?
They all have opportunity to smuggle drugs.
They’re all onboard the ship for the duration of its voyage.
They’re all trained in ship emergency procedures.
They’re all employees of the ship.
According to their physical state, extinguishing agents may be classified in to:
Solid, proteinic and gases.
Synthetic, proteinic, gases and liquid.
On the figure there are four (4) possible definitions of the term “ASTERN” shown. Which one is the correct one?
Astern is defined as C on the figure.
Astern is defined as B on the figure.
Astern is defined as D on the figure.
Astern is defined as A on the figure.
The best way to identify an IED is to:
Recognize its components.
Measure the size of the object.
During a bomb search, which of the following is an important principle to follow?
Do not touch any suspicious packages.
Throw any suspicious items overboard.
Know exactly what a bomb looks like.
Try to reach behind bulkheads to find a bomb.
What is the correct understanding of the term “boat deck”?
The deck where the top of the lifeboats can be viewed.
The deck of a ship at the base of the accommodation.
The deck which is at the top of the double bottom tank on a cargo ship.
The deck where the lifeboats davits are positioned.
The extinguishing agent which can be applied on any fires of class A, B or C is:
In general what is the proportion of concentrate to water to produce foam?
This operation is done automatically and in relation to the foam.
Which of these are indicators that an individual may be a drug smuggler?
The individual wears bulky or out of season clothing.
The individual spends his or her free time hanging out with others.
The individual makes small local purchases.
The individual is disinterested in the ship’s cargo.
On the figure there are four (4) possible definitions of the term “CENTRE LINE”. Which one is the correct one?
Centre line is given by B on the figure.
Centre line is given by C on the figure.
Centre line is given by D on the figure.
Centre line is given by A on the figure.
If drugs are discovered onboard your ship:
Ensure the witness to the discovery signs your incident report.
Disembark crew and passengers as quickly as possible at the next port of call so the authorities can conduct their investigation.
Write a report a few days after the event and describe everything that occurred.
Notify the authorities after you arrive at the next port of call.
Which of the following areas may be possible restricted areas? Review all answers.
On the figure there are four (4) possible definitions of the term “WINDLASS”. Which one is the correct one?
Windlass is given by C on the figure.
Windlass is given by D on the figure.
Windlass is given by B on the figure.
Windlass is given by A on the figure.
When acting as helmsman would you expect the reading of the gyro compass to be the same as the magnetic compass?
Very seldom would they be the same.
They would never be the same.
They would always be within 1 or 2° of each other.
They would always be the same.
Who is responsible for completing the DoS on behalf of the ship?
Company Security Officer.
What is the correct understanding of the term “Block Coefficient” as applied to a ship?
The comparison of the underwater shape of the ship, to a rectangular block of the same extreme dimensions.
The ratio of the waterplane shape of the ship to a rectangle of the same extreme dimensions.
The restriction of a valve in a pipe to the flow of fluid through that pipe.
The coefficient of a Block and Tackle.
The method of extinction by smothering is based on this basis:
The fire extinguished by avoiding the contact between the fuel vapours and the oxygen.
The fire is extinguished by eliminating the heat so as to obtain a temperature at which the fuel doesn’t give off enough vapour.
The fire is extinguished by interrupting the chain reaction, as it stops the transmission of heat by means of the action of chemical agents.
The fire is extinguished by avoiding the contact between the fuel vapours and the hot surface.
Who is authorised to operate lifting equipment around the ship?
Those ship’s personnel who have been assessed as competent and are duly authorised to do so by the master as per the procedures as outlined in the ship’s SMS system.
Deck officers and ratings, engineering officers and ratings, GP crew if applicable, who are in possession of crane operation training certificates issued by the company.
Stevedores manufacturer’s maintenance engineers and senior ratings only.
All the deck officers and ratings and selected engine-room personnel.
Via Inmarsat-C a message is sent to an Inmarsat-C mailbox with a positive delivery notification (PDN). The ground station will:
Send a PDN, if the message has arrived in the mailbox.
Send no PDN’s with messages intended for the mailbox.
Send a PDN, as soon as the message is collected from a mailbox.
The best way to identify an IED is to:
Recognize its components.
Measure the size of the object.
Which activity will have the greatest fire-fighting effect in case of a fire?
Extinguishing attempt is started immediately.
All fire-fighting teams are organized as soon as possible.
All possible fire-fighting equipment is brought to the scene.
Which of these are indications that a parcel is suspicious?
The parcel is addressed to no one in particular, arrives unexpectedly and seems heavy for its size.
The parcel smells like chocolate.
The parcel came from Joe in the safety department and arrived quicker than expected.
The parcel is wrapped in clean, brown paper and is addressed to a crewmember from his wife.
Which of these weapons are widely available and commonly used by criminals and terrorists to further their aims?
Which type of equipment can be used to detect explosives?
Which is the “CAPSTAN”, in the figure?
The Capstan is indicated by A.
The Capstan is indicated by B.
The Capstan is indicated by C.
The Capstan is indicated by D.
If the radar is set onto the Relative Motion Display, what would an echo of a target with no trail indicate? Note this the trail of the echo and not a vector.
The target is on the same course and speed as own ship.
The target is stopped and making no way through the water.
The target is on a constant bearing and getting closer to own ship.
The target is on a collision course with own ship.
What must be done after completion of ballasting operations on a bulk carrier?
All valves closed, tank ventilators in open position and sounding pipe caps replaced.
Sounding pipe caps left off.
All valves and lines left open.
All valves closed and tank ventilators to closed position.
A very dusty cargo is to be loaded on a bulk carrier; what precautions on deck should be included?
All cranes, deck houses and storerooms fully closed down to prevent entry of dust.
No access allowed onto main deck.
No extra precautions need to be taken.
Decks washed down regularly.
When preparing the hold of a bulk carrier for cargo when that hold has previously been ballasted, which of the following must be checked?
Previous cargo swept out.
The ballast lines must be blanked off and the bilge lines opened and tested.
The heating coils fitted.
Paint coating re-painted.
Could a lift be considered as an escape route from the engine room?
Yes, if it is constructed with class A materials.
It depends on the distance of the escape route.
If circumstances permit, how should low expansion foam be applied to oil burning near a bulkhead of the engine room?
The foam should be aimed at the bulkhead behind the fire and allowed to spread out slowly over the fire.
The foam should be aimed at about 45° upwards so that it can drop onto the fire.
The applicator should be used in a sweeping motion to spread the foam over the surface.
The foam should be applied to the centre of the fire.
“Overshoot” is an expression we use when talking about a ship’s steering ability. What is the definition of this expression?
It is the way a ship turns when you put the helm in a hard over position.
It is how many degrees a ship continues to turn after you apply counter rudder.
It is the way a ship shoots forward when you give “a kick ahead”.
It is the way a ship continues to turn when the helm is put amidship.
How can the effects of “Squat” be minimized, when a ship is proceeding in shallow water?
Maintain a slow speed just sufficient to maintain steerage.
Enter the shallow water with a stern trim and proceed at a moderate speed.
Decrease the speed and keep the ship to the centre of the channel where the water is probably deepest.
Maintain a speed of about 6 knots and use minimal rudder when manoeuvring.
When could there be a demonstration of how to start a lifeboat engine?
A demonstration could be arranged during a lifeboat drill.
There is an instruction card inside the lifeboat showing how to start the engine.
A demonstration is not necessary, because there are a limited number of persons who given the responsibility for starting the lifeboat engine.
Starting the lifeboat engine is very easy and there does not need to be any demonstration.
How does low expansion foam act as an extinguishing agent when dealing with oil fires?
By smothering and also by providing some cooling.
The heat from the fire causes the foam to produce an inert gas which gradually extinguishes the fire.
In a smoke filled alleyway where will the cleanest air be found, and how should you proceed out?
Near to the deck, crawl out keeping your face as near to the deck as possible.
Sit and wait for the rescue party.
It will be the same in all parts, therefore I would just leave as quickly as possible.
Towards the upper part, stand as tall as possible and walk out.
What is flashpoint of an oil or liquefied gas?
The flashpoint for an oil or liquefied gas is the temperature at which it is possible to ignite the vapour above the liquid.
The flashpoint is the temperature needed to have a oil or liquefied gas pumpable.
The flashpoint is the mixture of oxygen and hydrocarbons needed to have an oil or liquefied gas to burn.
The flashpoint is the temperature the oil or liquefied gas need for self ignition.
The aim of fire detection is:
All the answers are correct.
To discover where a fire starts.
To begin applying an emergency plan.
If a fire starts in the fuel tanks of a vessel, the fire will be:
Searches are often triggered by:
An increase in security level by the Flag State.
The receipt of a shipment of damaged stores.
News stories of stowaways.
In the diagram, which arrow is pointing at the position known as the “Bridge”?
The Bridge is indicated by A.
The Bridge is indicated by B.
The Bridge is indicated by C.
The Bridge is indicated by D.
What is the absolutely main purpose with fighting a fire on board?
What paint coating should be used in a cargo hold of a bulk carrier, when the hold may be used for the carriage of grains?
Approved for use in cargo spaces that may carry edible cargoes.
Any paint type can used in these spaces.
Paint must be epoxy based.
Cargo spaces must not be painted.
On the diagram, which letter indicates what is meant by the word “DRAUGHT” of the ship?
Draught is indicated by D, in the figure.
Draught is indicated by B, in the figure.
Draught is indicated by C, in the figure.
Draught is indicated by A, in the figure.
When can a partly loaded bulk cargo space be entered when the vessel is at sea?
For hatch cleaning purposes.
On instructions from the CPO (Bosun).
In no circumstances except possibly in an emergency.
In order to extinguish a flammable liquid of the same kind as alcohol, we can use:
What is the purpose of the Ship Security Plan?
Protect your ship from risks posed by security threats or incidents.
Outline specific measures for your ship to move from security level 1 to 2 and from 2 to 3.
Detail the duties of shipboard personnel assigned security responsibilities.
Outline the organizational structure for the ship.
Which of the following are frequent causes of fires in accommodation?
1 – Smoking in bed, 2 – Covering of electric fires with blankets, 3 – overloading electric plugs.
Covering of electric fires with blankets.
Overloading electric plugs.
Which statement about the use of profiling onboard a ship is true?
A random selection process must be established.
Detection equipment can be used in place of profiling.
Profilers need at least half an hour to gather the information they need.
Only visitors can be profiled.
Which of these actions should crew take if a suspicious object that may be a bomb is located during a search?
Confirm with their search partner that the object found is suspicious.
Place the object in a desk drawer or file cabinet.
Throw the object overboard.
Cover the suspicious object with a box or blanket.
This device can detect a package of drugs inside a large delivery of ship’s stores. What is it?
When handling drugs:
Wear skin protection and a facemark.
Shut off the ventilation in the room where the drugs are being stored to ensure any vapours or fumes do not spread to other parts of the ship.
Test out the potency of the drug.
Briefly inhale powders, fumes or vapours to verify the substance is a drug.
When is a visitor onboard required to present an ID?
On SECURITY Level 1, 2 & 3.
Only on SECURITY Level 3.
Which of these types of information is considered sensitive?
Voyage itinerary and departure and arrival times.
Planned maintenance schedule and emergency response procedures.
Way points and training records.
Ship schematic and HR policies.
To guarantee optimal reception of VHF-DSC calls, every:
DSC-symbol is sent twice and checked extra by Error Check Character.
DSC-report is sent twice, at least every second call is compared with the earlier received call.
DSC-calls are repeated until received.
DSC-symbol is checked on the right amount of 10, and then checked on the correct relation by Error Checked Character.