%20scale(3)'%3E%3Cpath%20id='s'%20d='M0,-30%2017.63355,24.27051%20-28.53171,-9.27051H28.53171L-17.63355,24.27051z'%20fill='%23FF0'/%3E%3C/g%3E%3Cuse%20xlink:href='%23s'%20transform='translate(300,60)%20rotate(23.036243)'/%3E%3Cuse%20xlink:href='%23s'%20transform='translate(360,120)%20rotate(45.869898)'/%3E%3Cuse%20xlink:href='%23s'%20transform='translate(360,210)%20rotate(69.945396)'/%3E%3Cuse%20xlink:href='%23s'%20transform='translate(300,270)%20rotate(20.659808)'/%3E%3C/svg%3E){kind=small}
Suche nach aktuellen Stellenangeboten:
Filter anzeigen
Suche in der Datenbank der Lebensläufe von Seeleuten:
Heim Online-Tests CES Bulk Carrier MASTER / Ch-Officer Test for seafarers about Hatch Cover Maintenance on Bulk Carrier (CES)
Online-Test: Test for seafarers about Hatch Cover Maintenance on Bulk Carrier (CES)
Online-Test
Beschreibung
Rezensionen
Der Test besteht aus 80 zufälligen Fragen.
Gesamtzahl der Fragen zu diesem Thema: 98
Gesamtzahl der Fragen zu diesem Thema: 98
Frage 1 aus 80
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- 25
- 26
- 27
- 28
- 29
- 30
- 31
- 32
- 33
- 34
- 35
- 36
- 37
- 38
- 39
- 40
- 41
- 42
- 43
- 44
- 45
- 46
- 47
- 48
- 49
- 50
- 51
- 52
- 53
- 54
- 55
- 56
- 57
- 58
- 59
- 60
- 61
- 62
- 63
- 64
- 65
- 66
- 67
- 68
- 69
- 70
- 71
- 72
- 73
- 74
- 75
- 76
- 77
- 78
- 79
- 80
Which of the following procedures should be followed immediately after replacing a hatch seal?
The seal compression should be measured and recorded.
The lid should be closed as tightly as possible and left closed until arrival in the next port.
The groove in the seal should be measured in the forward corners of the hatch.
The appearance of the new seal should be compared to that of the old seal.
In additional to ensuring that cleats are properly applied, which of the following are checks that would be made as the hatches were being secured after closure? Select all applicable answers:
Antwort
Which of the following must there be a comprehensive record of, in order to be able to demonstrate “due diligence”?
Antwort
Which of the following, as highlighted in this module, are known to regularly block drainage channels and non-return valves? Select all applicable answers:
Antwort
If a ship’s hatches have been properly maintained and closed securely and properly, but are found to have leaked in abnormally severe weather, which of the following may form evidence that may be submitted in defence of a cargo claim? Select all applicable answers:
Antwort
What is considered to be an acceptable reading in an ultrasonic test? As per the general industry standard quoted in this module.
Any reading less than 10 % of the open-hatch reading.
Any reading less than 10 % of the closed-hatch reading.
Any reading more than 10 % of the open-hatch reading.
Any reading more than 1 % of the closed-hatch reading.
What is “permanent set”?
The groove in the hatch seal face, resulting from the loss of elasticity.
The exact position in which the hatch cover rests when closed.
The limit of good steel on the compression bar down to which steel deterioration may be considered acceptable.
The group of hatch seals which are in continuous contact with the coaming compression bar when the hatch is closed.
The exact angle at which the hatch cover lies when closed.
The distance from the outer edge of a rubber hatch cover seal to the middle of the groove created by the penetration of the compression bar, measured in mm and averaged from readings taken on all four sides of the hatch.
Which of the following figure in the top ten reasons for cargo damage based on water damage, as listed in this chapter?
Antwort
Which are the types of test commonly employed to determine the water tightness of hatches or other openings? Select all applicable answers:
Antwort
What normally determines the size of lift-away (pontoon) covers on container ships?
That they are capable of being lifted by shore-side container gantry cranes.
That they are capable of supporting a minimum four-stack of 40′ containers.
That they are fitted with an adequate number of anti-lift bolts to resist anticipated upward forces generated by stacks of containers as identified in the ship’s cargo handling manual.
That the longitudinal length of any one hatch cover does not exceed 0,25 of the registered length of the vessel on which it is fitted and the width is not more than 0,85 of the moulded breadth.
When considering the strength of a hatch cover, what kind of loads must it be able to withstand? Select all applicable answers:
Antwort
What is the class requirement for a hose test?
Nozzle of 15-18 mm in diameter, water pressure of about 2 bar, the jet of water aimed not more than 1 metre from, and directly at, every part of the sealing areas, moved at not more than 1 metre per 3 seconds, where the hatch covers are closed and cleated.
Nozzle of 10-15 mm in diameter, water pressure of about 3 bar, the jet of water aimed not more than 1 metre from, and directly at, every part of the sealing areas, moved at not more than 1 metre per 10 seconds, where the hatch covers are closed but not cleated.
Nozzle of 20-24 mm in diameter, water pressure of about 1,5 bar, the jet of water aimed not more than 1,5 metres from, and directly at, every part of the sealing areas, moved at not more than 1 metre per 5 seconds on the cross-joints and 1 metre per 3 seconds on the peripheral joints, where the hatch covers are closed and cleated.
Which of the following are among the critical hatch cover spares to be carried on board, as recommended in this program? Select all applicable answers:
Antwort
When replacing the straight pieces of a hatch seal, what is the recommended additional percentage to be allowed when cutting?
3 %.
1 %.
5 %.
None, it should be cut to the exact length required.
In terms of strength, what kind of loads must a hatch cover be able to withstand? Select all applicable answers:
Antwort
What is the name given to the substitute arrangement frequently fitted to the drain pipe in place of a non-return valve?
Sock.
Plug.
Guide.
Tube.
Socket.
Boot.
You are carrying out maintenance on number 3 hatch cover. The permanent set has reached half the design compression in places and there are signs of wear. You have cut out two metres of bad seal along the port side. What length of rubber will you actually cut to insert in its place?
2,06 m.
2 m.
1,94 m.
2,03 m.
1,97 m.
What will an inspection prior to discharge primarily establish?
Whether the measures taken in sealing the hatch after loading were successful.
Whether there is any damage to the hatch cover panels.
Whether there is any damage to the trackway.
Whether the hatch was closed properly.
If personnel are in, or could be in the vicinity of a hatch cover, what should you do before you open or close it?
Use all available means of communication to notify them that a hatch cover movement is about to take place.
Nothing – it is for them to take due care.
Ask them to leave the area.
Walk all around the hatch cover, so that you can complete the “inspection” section of the safety checklist.
Under standard operating conditions and with proper handling, what might the expected life expectancy of a rubber hatch seal be (as quoted in this program)?
4-5 years.
6 months.
1 year.
2 years.
10-12 years.
What general rule does this program suggest designers of hatch covers, those who maintain them and those who operate them should direct their efforts towards?
Defending the thin line where the compression bar and the seal rubber meet.
Minimizing the time delays due to opening and closing of hatch covers.
Ensuring seals must be resilient or elastic enough to make up for hull and coaming deformations.
That intervals between replacement of hatch seals are maximised.
Which of the following are suggested in this chapter as examples of relatively low cost preventative measures that may prevent expensive cargo claims? Select all applicable answers:
Antwort
What is the unique different design feature in a side-rolling, chain-drive “piggy-back” hatch cover arrangement?
A dumb panel with no wheels is lifted by hydraulic lift cylinders fitted to the coaming, a rolling panel is moved underneath it and the dumb panel is lowered onto the rolling panel, which is then driven to one side as the hatch is opened.
No direct hydraulic power is used and the hatches are opened by an arrangement of wires or chains.
The panels are lifted one on top of the other at one end of the hatch coaming by means of a travelling gantry crane.
A special flexible hinge arrangement allows the hatch cover to turn through 180° and fold back on top of an adjacent panel.
Which of the following is a description of the function of periphery cleats around a hatch cover?
They provide vertical restraint, stopping the panel lifting, while permitting some relative movement between the coaming and the cover.
They provide horizontal restraint, control the cross-joint seal compression and ensure the edges of the hatch cover panels at the cross joint remain firmly pressed or held together and that the cross joint seal rubber remains properly compressed.
They provide transverse restraint, restricting the horizontal movement of the panel, ensuring that the compression bar remains within the groove in the hatch seal.
In order to understand the basic principle behind hatch cover design, how must the hatch be considered?
As a dynamic (mobile) object on the coaming.
As a static object on the coaming.
As a rigid object on the coaming.
As an open area continually exposed to salt water.
A prime cause of early failure of hatch seals is over-compression caused by corrosion or breakdown of the steel-to-steel contact. Cleats are then frequently over-tightened in an attempt to compensate. But what types of failure does this action commonly result in? Select all applicable answers:
Antwort
In a four-panel arrangement, the cylinders are operated once the cleats are all released, causing the first, or “leading” pair of panels to peak. At this time, what is happening to the second pair of panels?
The wheels of the “trailing pair” roll up onto their trackways.
They are also “peaking” in parallel.
Nothing is happening to the second pair of panels. They are totally independent.
The third panel is raised at 45° and the fourth is about to begin elevating.
Before attempting to open the hatch covers, what should happen to all cross-joint cleats and wedges?
They should be disengaged.
They should be engaged.
They should be greased.
They should be examined for signs of wear or failure.
What additional fixtures are found on lift-away (pontoon) covers?
Large locators, to absorb the forces caused by deformation of the coaming when the ship is working in a seaway.
Quick-acting cleats.
Elliptical drive wheels.
A bell crank on each side.
You are on board a bulk-carrier, in ballast, at sea. You are to clean and examine the inner faces of the side-rolling hatch covers on no 2 hold. What particular safety measure is required?
Safety fencing, consisting of portable stanchions with an upper and lower safety wire, should be in place.
Nothing particular is required.
Ensure the covers can move freely at any time.
All personnel not directly involved in the inspection should leave the deck.
Personnel should be instructed not to climb up onto the hatch cover at any time.
Which two areas have been specifically identified in this chapter as being vital to the safe and successful execution of the cargo handling process?
Antwort
If there has been water ingress on passage, how will this normally be seen?
It will usually follow the pattern of the cross-joint and coaming seals.
It will be under the most forward panel on a hatch.
It will be on the centreline.
It will be at the sides of the cargo, having run down the sides of the hold.
Article III, rule 1 of the Hague-Visby Rules requires the carrier to fulfil which of the following conditions? Select all applicable answers:
Antwort
In order to be able to demonstrate “due diligence”, which of the following must there be a comprehensive record of?
Antwort
Which of the following figure in the top ten reasons for cargo damage based on water damage, as listed in this chapter?
Antwort
Which of the following may be seen as arguments against using hatch sealing tape? Select all applicable answers:
Antwort
You are to carry out some minor repairs to a hatch coaming. The vessel is at sea. Which of the following measures should be in place prior to commencing the work? Select all applicable answers:
Antwort
Where would you find information on routine maintenance, operation and safety issues related to hatch covers, including the greasing program for various components, notes on the care of wire ropes and fittings and details of the hydraulic system?
The operating and maintenance manual.
The classification society handbook.
SOLAS.
The spares catalogue.
Which of the following can be seen as potential limitations of a hose test? Select all applicable answers:
Antwort
Which of the following do industry statistics indicate as being the cause of a high proportion of reported cargo-worthiness defects?
Hatch covers, their seals and securing arrangements.
Cargo containers.
Cargo handling cranes, wires and control systems.
Untypical weather conditions.
How does a side-rolling, chain-drive “piggy-back” hatch cover work?
A dumb panel with no wheels is lifted by hydraulic lift cylinders fitted to the coaming, a rolling panel is moved underneath it and the dumb panel is lowered onto the rolling panel, which is then driven to one side as the hatch is opened.
The hatches are opened by an arrangement of wires or chains, which stack the hatches one on top of the other at one end of the hatch coaming.
The panels are lifted one on top of the other at one end of the hatch coaming by means of a travelling gantry crane.
A special flexible hinge arrangement allows the first hatch cover to turn through 180° and fold back on top of the second panel; these two then rotate together, coming to rest on top of the third panel and so on.
In respect of any repairs to hatch covers, with whom does the ultimate responsibility lie under the laws governing the carriage of goods by sea?
The ship-owner.
The designated subcontractor.
The ship’s officers.
The charterer.
Why is a chalk test considered to have limited value in establishing the water tightness of a cargo hatch cover?
Because it gives no indication of the amount of seal compression that exists when the ship is actually underway in a seaway.
Because it does not show where the rubber comes into contact with the compression bar.
Because it is out carried out at sea.
Because it is carried out before any cargo is loaded.
Because compression of the seal is marginal.
What is the generally accepted rule applied to determine when the seal has reached the point of replacement?
When permanent set reaches half the design compression.
When permanent set reaches full design compression.
When a groove is seen in the seal.
After not less than 9 months and not more than 15 months service.
Defective hatch covers are particularly associated with vessels of which of the following age brackets?
10-20 years.
0-3 years.
5-10 years.
25-30 years.
What obligation is there on the ship-owner, in respect of the carriage of goods by sea?
To exercise due diligence to make the ship seaworthy.
To carry goods in the most expeditious manner, irrespective of risk.
To be seen to comply with the prevailing regulations when audited or inspected.
To carry a copy of the Hague-Visby rules on board.
In terms of the sealing of a hatch cover, what are the design requirements? Select all applicable answers:
Antwort
What are the two main aspects to the maintenance of hatch covers in service, as identified in this program?
Antwort
The annual survey of hatch covers is carried out in compliance with which of the following? Select all applicable answers:
Antwort
As quoted in this chapter, which of the features listed below, render all hatch covers potentially dangerous? Select all applicable answers:
Antwort
What is the minimum length of any straight piece of rubber seal inserted during a repair, as recommended in this module?
500 mm.
700 mm.
300 mm.
200 mm.
750 mm.
1 000 mm.
Which of the following may be considered as key design elements of hatch design? Select all applicable answers:
Antwort
In which of the following operational conditions would a seal with a sponge core with an outer skin made of nitrile rubber commonly be used?
For oil cargoes on an OBO vessel.
Where there are very heavy hatch covers.
On side-rolling cover fitted to a bulk-carrier.
On vessel with large open hatchways, where coaming movement will be a problem.
Which of the following are common patterns of peripheral cleat? Select all applicable answers:
Antwort
Why might a chalk test be favoured over other forms of test in certain circumstances?
If loading has already been completed and there are suspicions that a hose test could present a risk to that cargo.
Because it gives a more reliable indication of conditions prevailing when the ship is at sea.
Because it delivers a more even measurement of the seal around the entire hatch coaming.
Because it is the method most favoured by cargo surveyors.
When de-ballasting is about to start, why is it necessary to have the vents on water-ballast hatches open?
If they are closed, the tank may collapse under vacuum.
Because it is a requirement on the safety checklist.
Because it makes cleaning easier.
If they are closed, they may be forgotten when the ship goes to sea.
When considering the security of a hatch cover arrangement, what measures must be incorporated in the design specification? Select all applicable answers:
Antwort
In which of the following operational conditions would an extruded hollow section seal commonly be used?
On side-rolling cover fitted to a bulk-carrier.
For oil cargoes on an OBO vessel.
Where the vessel trades in Arctic conditions.
On vessel with large open hatchways, where coaming movement will be a problem.
You have just replaced the seal on number 2 hatch. What should you do now?
Measure the seal compression and record it.
Secure the lid as tightly as possible and leave it closed until arrival; in the next port.
Measure the groove in the seal in the forward corners of the hatch.
Compare the appearance of the new seal to that of the old seal.
Prior to closing hatch covers, which of the following should be standard safety checks? Select all applicable answers:
Antwort
What is the minimum length of any piece of rubber seal inserted during a repair, as recommended in this module?
500 mm.
700 mm.
300 mm.
200 mm.
750 mm.
1 000 mm.
If a ship’s hatches have been properly maintained and closed securely and properly, but are found to have leaked in abnormally severe weather, which of the following may form evidence that may be submitted in defence of a cargo claim? Select all applicable answers:
Antwort
Which of the following may be considered as key design elements of hatch design? Select all applicable answers:
Antwort
If it is assumed that the covers have been properly installed, which of the following lead to the majority of the problems of accelerated wear of hatch seals? Select all applicable answers:
Antwort
What technique do automatic cleats employ to hold the hatch firmly in place once closed?
Wedges on the hatch cover engaging mechanically in matching wedges on the coaming.
They slide across like a wedge bolts.
They are applied and tightened using hydraulic cylinders to provide the force.
They are dropped into place and then tightened up with a spanner.
In freezing conditions, what can be done to prevent the rubber hatch seal sticking to the compression bar during closing?
A non-organic grease or commercial glycerine should be spread on the compression bar prior to closure.
The rubber hatch seal should be heated with steam or a blowlamp prior to closure.
The hatch seal should be replaced with special reinforced compound sealing material.
Whale grease should be applied to both the compression bar and the hatch seal surface 10 minutes before closing is required.
Which of the following must there be a comprehensive record of, in order to be able to demonstrate “due diligence”?
Antwort
What type of hatch cover is frequently fitted with an indirect cross-joint cleating arrangement, where wedge-shaped battening devices attached to the covers engage in coaming sockets, causing the panels to be forced together as they are lowered onto the coaming?
Side-rolling covers.
Four panel folding covers.
Stacking covers.
Pontoon covers.
Which of the following are acknowledged challenges to the ship’s officers and crew, in terms of maintenance of their hatch covers and associated fittings? Select all applicable answers:
Antwort
It is February 3rd. You have just loaded a cargo of gravel in Trondheim, Northern Norway. You anticipate that, if you close the cargo hatches, the rubber hatch seal may stick to the compression bar. What can you do to prevent this?
Spread a non-organic grease or commercial glycerine on the compression bar prior to closure.
Heat the rubber hatch seal with steam immediately prior to closure.
Replace the hatch seal with special reinforced compound sealing material.
Apply whale grease to both the compression bar and the hatch seal surface 15 minutes before closing the hatch.
In additional to ensuring that cleats are properly applied, which of the following are checks that would be made as the hatches were being secured after closure? Select all applicable answers:
Antwort
What is the function of the non-return valves fitted to the drain pipes at the corners of the coamings?
To permit water to drain freely onto the deck but stop water from the deck entering the hold.
To permit air to enter the hold and allow water to drain freely onto the deck.
To stop water from, but allow air into, the hold.
To allow water to drain from and allow air into, the drain pipes.
Which of the following is checked at an annual survey? Select all applicable answers:
Antwort
Which of the following age brackets are particularly associated with defective hatch covers?
10-20 years.
0-1 year.
0-10 years.
20-30 years.
In an ultrasonic test, what is the severity of a leak referenced to?
The open-hatch reading.
The closed-hatch reading.
The reading obtained on the opposite side of the hatch.
The calibration reading obtained in the surveyor’s laboratory.
Who are best placed to continuously monitor the operational condition of hatch covers and sealing arrangements on board?
The ship’s officers and crew.
Cargo surveyors.
The company superintendent.
Stevedores.
Which of the following are common patterns of cross-joint cleat? Select all applicable answers:
Antwort
Which of the following are considered to be the most common forms of hatch cover type? Select all applicable answers:
Antwort
The Hague-Visby Rules require the carrier to properly and carefully load, handle, stow, carry, keep, care for, and discharge the goods carried. The “carefully-to-carry” clause includes which of the following requirements?
That the ship-owner and the master of the ship must understand the nature of the cargo carried and the extent of the precautions necessary to look after it.
That the ship-owner must understand the process of wear and tear resulting from the carriage of cargo and ensure the master pursues a program of regular inspection and maintenance.
That the charterer must understand the nature of the cargo carried and ensure the ship-owner and master of the ship exercise due diligence in its carriage.
That the master of a vessel will exercise due diligence in his responsibilities to the owner of the cargo, the operator of the vessel and to the environment.
Industry statistics clearly indicate a high proportion of reported cargo worthiness defects as being caused by which of the following areas of operation?
Hatch covers, their seals and securing arrangements.
Cargo containers.
Cargo handling cranes, wires and control systems.
Untypical weather conditions.
Negligence in securing the ship for sea.
Overloading.
Добро пожаловать! Оцените уровень своих знаний с помощью стандартной системы оценки экипажа CES (Crew Evaluation System) по теме «Hatch Cover Maintenance on the Bulk Carrier» (Техническое Обслуживание Грузовой Крышки Люка на Сухогрузных судах). Данный тест поможет вам, как морскому специалисту, подготовиться к сдаче экзаменов, получению сертификата компетентности или аттестата.
Nur Segler können Bewertungen hinterlassen. Um eine Bewertung abzugeben, melden Sie sich mit Ihrem Sailor-Konto auf der Website an.
Seien Sie der Erste, der diesen Online-Test bewertet!