Главная Онлайн-тесты CES Passenger MASTER / Ch-Officer Онлайн-тест CES 5.1 для MASTER / Ch-Officer, Passenger vessel

Онлайн-тестирование: Онлайн-тест CES 5.1 для MASTER / Ch-Officer, Passenger vessel

Вы можете начинать тест

Выберите режим работы с тестом:

Режим обучения

Прохождение теста

Онлайн-тест

Описание

Тест состоит из случайных вопросов по выбранной теме.

Вопрос 1 из 90

You are on board a ship which is not specially fitted for navigation in cold regions. At what ambient temperature should the engine of the lifeboat *start within less than 2 minutes ?

until - 15°C

until - 5°C

until - 3°C

until - 0°C

Among working conditions listed below which one is required for every propulsion engine of lifeboats?

Propeller permanently driven by the engine

For a period of at least 72 hours

Self-starting and launch procedure simultaneous

Sufficient fuel to run at 6 knots for a period of at least 24 hours

Welding and use of open flames on board tankers( without COW and IGS) in operation are subject to regulations laid down by the Norwegian Maritime Directorate (Norwegian Ship Control Legislation - NSCL). Which of the listed requirements regarding washing and gas freeing before hot work in cargo tanks corresponds to these regulations? (NSCL 22/1294/4).

Hatches to not adjacent tanks which has not been cleaned or inerted shall be kept open during work.

All cargo tanks, pump rooms and cofferdams shall be examined by type approved two explosimeters.

Gas measurings can be carried out by all deck officers.

One type approved explosimeter shall be used for gas measuring.

*Which of the following instructions or information SHALL be contained in the Training Manual?

use of breathing apparatus

means of escape or escape routes

emergency repairs of fire-fighting equipment

use of communication equipment

Which one of the listed fire-extinguishing medium is to be preferred to fight a fire in an electric installation (for example the main switchboard)?

Powder.

Foam.

Water fog.

Sprinkler.

You wish to send a message with the Inmarsat-A fax-installation to an Inmarsat-C installation. This is:

Possible with the help of shore installation

Not possible

Possible

Only possible when the Inmarsat-C installation has a fax device

The battery of an EPIRB should be changed

Every two years

Every four years

Every three years

Yearly

To announce an important navigational –or meteorological warning via the VHF-installation, one should use the:

urgency call

safety call

distress call

Don't know

What is false regarding the function :” Transmission and reception of ship to ship distress alerts

On area A4 this function is based on the use of VHF or/and MF DSC

On area A2 this function is based on the use of VHF or/and MF DSC

On area A3 this function is based on the use of INMARSAT A, B or C

On area A1 this function is based on the use of VHF DSC

Which word will precede a safety message ?

PAN PAN

SAFETY

SECURITY

URGENT

The word EIGHT is spelled conform the international phonetic alphabet:

Echo, India, Golf, Hotel, Tango

Echo, Israel, Golf, Hotel, Tango

Don't know

Echo, Istria, Gulf, Hotel, Tango

Which of the following is a Accounting Authority Identification Code?

F1B

2187.5

FR01

227990850

In discussing the properties of chemical cargoes, what is the "Odor Threshold" of a product?

The smallest concentration, expressed in parts per million by volume in air, that can be detected by smell by most people.

The maximum concentration of a vapour that can be tolerated without permanent damage to the nasalmembranes.

The temperature at which the vapour pressure a substance is greater than the prevailing atmospheric pressure and vapour is then released into the environment.

The average concentration of a substance to which a worker may be repeatedly exposed for a normal 8 hour working day, 40 days a week, without adverse health effects.

Give the meaning of the following symbol

Primary means of escape

C class division

B class division

A class division

What is the vessel that has the local command in a rescue operation called?

Commander of Operation

Local Rescue Commander

On Scene Commander

Commander of Rescue Operation

You are in confined waters. Is there any danger in the situation sketched below if you should lose engine power?

She will sheer slowly to port

She will drift to port, but rather slowly as you are loaded

Your ship will sheer to starboard rather quickly with the possible consequence of grounding

Your ship will lose headway, but there should be no immediate danger

An area A2 is:

an area excluding sea area A1 within the radiotelephone coverage of at least one MF coast station in which continuous watch on 2182 kHz is available

an area excluding sea area A1 which extend to 100 nautical miles from the coast stations

an area within the radar coverage of at least one MRCC in which a continuous DSC alerting is available

an area excluding sea area A1 within the radiotelephone coverage of at least one MF coast station in which continuous DSC alerting is available

VHF channel 15 is:

Public traffic channel

Distress channel

Contra-ship channel

Inter-ship channel

The wavelength of a radio-signal reflected against the F-layer may be:

1.5 m

Don't know

15 m

15 cm

Vessels communicating with each other by mariphone, work:

always simplex

always semi-duplex

Don't know

dependent on the set onboard

Define the class of emission H3E :

Radiotelex and DSC - Frequency shift keying of carrier with error correction

Radiotelephony - Single sideband full carrier

Radiotelex and DSC - Phase modulation

Radiotelephony - Single sideband suppressed carrier

Which of the following is a SART transponder frequency :

121,5 MHz

VHF 70

9 GHz

2182 kHz

What is the fundamental purpose of a coast radio station?

To automatically connect a vessel placing an INMARSAT call with the station being called.

To coordinate search and rescue communications.

To provide continuous digital selective calling coverage.

To provide a delivery service for ships with routine, safety, urgency, or distress message traffic.

Which of the following information shall be specified by the muster list ?

the specific duties assigned to passengers that are in charge of a group of others

the abandon ship signal consisting of two long blasts

the muster list has been prepared and approved by the Administration before the ship proceeds to sea

how the order to abandon ship will be given

Which item among those below is included in the normal equipment of every lifeboat ?

a VHF transceiver

one immersion suit for each person

sea-charts and navigating equipment

one set of fishing tackle

Give the meaning of the following symbol

Rocket parachute flares

Survival craft portable radio

EPIRB

Radar transponder

Give the meaning of the following symbol

EPIRB

Radar transponder

Survival craft distress pyrotechnic signals

Rocket parachute flares

*Which of following items shall be included in an abandon ship drill?

Checking the lifeboat provisions and supplies

lowering of at least one lifeboat after any necessary preparation for launching

Checking passenger's immersion suits

Checking the distress signal rockets and other distress signals

Which of the following detailed explanations should be mentioned in the Training Manual ?

The use of escape routes and other escape methods

The use of navigational equipment for survival crafts

The use of all survival equipment

The use of surface to air visual signals to be used by survivors

Which international regulations govern the disposal of waste material, including galley waste, from ships?

Chapter II, SOLAS 1974.

The Industry Best Practise Guide for Restaurant Management.

Annex V, MARPOL 73/78.

Section III, ISPS Code.

What is the weather associated with being in the centre of an Anticyclone (a region of High Pressure)?

Persistent rain and very humid weather

Strong winds and heavy rain

Strong winds but with very little rain

Light winds and fair weather, sometimes fog.

What would be a typical set point for emergency shut down of a large slow speed diesel engine due to "lubricating oil inlet to camshaft" low pressure?

0.1 bar

5 bar

0.4 bar

1.5 bar

The typical current gain of a common emitter transistor is

10-200

500-5000

1-1000

1-10

Which of the following parameters will result in oscillation

Too short D-time

Too high amplification

Temperature change

Too long I-time

The IMO Gas Codes require that all liquefied gas carrier cargo tanks are fitted with pressure relief valves. Pilot operated relief valves are frequently used, particularly with refrigerated cargoes. What is the main advantage of using pilot operated relief valves rather than simple spring loaded types for refrigerated liquefied gas cargoes tanks?

The set pressure can be adjusted to above MARVS if problems occur with the reliquefaction plant.

When pilot operated valves are used only one valve per cargo tank is required irrespective of tank size.

They ensure accurate operation at the very low cargo carriage pressures.

They ensure accurate operation at the very low cargo carriage temperatures.

Who is responsible for the development of the Ship Security Plan?

The Port Facility Security Officer

The Classification Society.

The Company Security Officer

The Ship Security Officer

Which of the following fluids usually has the lowest density at normal ambient temperatures?

Marine diesel oil.

Heavy fuel oil.

Lubricating oil.

Sea water.

"If drugs or suspected drugs are found onboard your ship, follow the five C’s. Confirm, Clear, Cordon, Control and:"

Check

Chuck

Change

Cheer

What do the shapes that this vessel is displaying tell us about here?

That she is restricted in her ability to manoeuvre and making way through the water. She is seen head-on, but we do not know her length.

That she is engaged in towing, but we do not know her length, or the length of her tow.

That she is not under command, but is still making way through the water. She is seen head-on, but we do not know her length, although it is probably over 50 metres.

That she is not under command and not making way through the water. She is seen head-on, but we do not know her length.

What is "Viscosity"?

The property of a liquid which determines its resistance to flow.

The scale which records the pour point of liquids.

The ability of a substance to overcome friction.

The term used to

What is shown in the image?

A hatch compression bar is shown in the image

A hatch cleat is shown in the image

A hatch wedge is shown in the image

A hatch locking bar is shown in the image

Which IMO convention takes care of the human safety at sea?

It is the MARPOL that takes care of the human safety at sea.

There are not any conventions that take care of the human safety at sea.

It is the STCW that takes care of the human safety at sea.

It is the BCH Code that takes care of the human safety at sea.

What should be done in preparation for loading cold rolled steel sheets in bulk carriers?

8mm wire cables should be laid athwartships over the tank top spaced 5m apart

Dunnage should be laid athwartships over the tank top

Dunnage should be laid fore and aft over the tank top

16mm wire cables should be laid fore and aft over the tank top spaced 3m apart

A Bulk Vessel is to load a cargo of grain; pre loading calculations show that IMO stability criteria cannot be achieved; the vessel should do which of the following?

The grain surfaces in some or all of the cargo spaces must be secured

The cargo can still be loaded

An exemption certificate must be applied for

The vessel will be unable to load the cargo

What would you do before giving a boiler a “bottom blow”

Increase the oil temperature

Drop the water level a couple of inches below normal

Increase the oil pressure

Raise the water level a couple of inches above normal

Emergency instructions in appropriate languages shall be posted in passenger cabins. What information shall as a minimum be included in the emergency instructions?

Name of cabin attendant

Escape routes and alarm signals

The method of donning life-jackets, escape routes and alarm signals

Where to find thermal protective aids

Where and for what are rubber mats used on board a pure car carrier?

Under the loading ramp flap to prevent jetty damage

On the loading ramp to prevent damaging the ramp surface

Under the loading ramp flap to prevent vehicle damage

Two identical medium speed engines are connected through clutches and a reduction gearbox to a single controllable pitch propeller. It is noted during normal operation that the load sharing between the engines is uneven with one engine taking a greater proportion of the load as the total load increases even though they are equally loaded at low load. Select from the options given the most likely cause of this problem.

One of the engines is running faster than the other at high loads.

The fuel filters in the supply line for one of the engines are blocked

The governor droop settings are incorrectly set and are not matched.

The clutch on one engine is slipping.

What measures should be taken in order to avoid flammable gases forming on top of coal cargoes on a Bulk Carrier?

Ventilation to be continuous?

Ventilation to be carried out as indicated in the IMO solid Bulk Cargo Code

Cargo to be ventilated by opening hatch covers at sea?

Cargo not to be ventilated?

What procedures should prevent normal ship work activities conflicting with cargo operations on a General Cargo Vessel?

Stevedore and Chief Officer planning meetings

Masters standing orders

Ships Security Code

Risk assessments and permit to work systems

How is the prime mover load normally kept to a minimum when starting up an electric driven reciprocating type air compressor?

By using an unloading device to keep the compressor delivery valves open until the machine is up to speed.

By using an unloading device to keep the compressor suction valves open until the machine is up to speed.

By keeping the second stage drain valve open until the machine is up to speed.

By keeping the main discharge valve closed until the machine is up to speed.

Where is there a likelihood of inadequate initial design on a bulk carrier?

Around the hatch corners

On cross-deck plating

On the sheer strack

On shell plating

Which function is this operational amplifier circuit performing?

Integrator

Differentiator

Non-inverting amplifier

Inverting amplifier

A reefer vessel is to load a part cargo of frozen beef hocks (large joints of beef, usually quarters, not packed in cartons). In deciding which would be the most appropriate space on a conventional reefer vessel, which of the given options would be the preferred choice?

Any space will be acceptable as this is a hard frozen cargo and relatively easy to handle and carry.

4A deck as this is the largest square space on the vessel and will allow good access and air flow for the cargo.

A cargo space low in the vessel as this cargo has a relatively high stowage factor.

1C deck as this is the narrowest space on the vessel and will best constrain the cargo from any possible movement during the voyage.

You are on a sailing vessel, underway in open water. This vessel is sighted on the starboard bow, on a steady bearing and the distance is closing. By the International Regulations for the Preventing Collisions at Sea, what action will you follow?

This vessel is clearly a power-driven vessel and I anticipate that the bearing will therefore close and she will pass ahead at a safe distance.

Risk of collision is deemed to exist and, as the other vessel is on a steady bearing on my starboard side, I am required to keep out of the way. I will make a broad alteration of course to starboard.

Risk of collision is deemed to exist and, as the other vessel is on a steady bearing on my starboard side, I will maintain my course and speed.

By Rule 18, a power-driven vessel underway shall keep out of the way of a sailing vessel. I will maintain my course and speed, but will continue to monitor situation to ensure the other vessel takes avoiding action.

Are membrane tanks self supporting as the independent tanks?

Membrane tanks are self-supporting only when they are loaded

Only the inner membrane is self-supporting

Membrane tanks are not self-supporting

Membrane tanks are self-supporting as the independent tanks

You are to load a cargo of Cyclohexanol to tanks 2, 3 and 4 centre and 2 and 4 wing tanks. The lines to these tanks are all connected at the manifold with flexible hoses and are all capable of being isolated with the exception of 2 centre, which has therefore been designated as the last tank to load. What will you do with the other tanks as they complete loading?

Close only the tank loading valves, so that pressure remains constant around the pipeline system and flexible hoses. Continue to monitor the cargo levels in the finished tanks to ensure that the high-level alarms are not activated as the ship's trim changes.

Close only the corresponding manifold cross-over valves as the tanks finish, so that the pressure in the lines equalises with the pressures in the tanks. Re-check the ullages at the end of loading as they will have changed as the trim of the ship has changed.

Close the tank loading valves, then close the appropriate manifold cross-over valves. After a few minutes, re-open the tank loading valves and leave them like this until cargo operations are completed, to ensure they drain fully. Re-check the ullages at the end of loading and then close the tank loading valves.

Close the appropriate manifold cross-over valves and tank loading valves as each tank finishes. Continue to monitor the cargo levels in the finished tanks to ensure that the valves are not passing.

Where should the vehicle belonging to a disabled person be placed?

Preferably near an elevator or a place where you have easy access to the stairways

Near the stairways

In the after part of the car deck

As close to the bow door as possible to avoid any traffic jam during discharging

The IMO Cargo Stowage and Securing Code (CSS) indicates in the 'Rule of Thumb', the total strength of the lashings on each side of a heavy lift; what is the stated value ?

The Maximum Securing load of the lashings must equal five times the weight of the cargo unit

The Maximum Securing load of the lashings must equal the weight of the cargo unit

The Maximum Securing load of the lashings must equal twice the weight of the cargo unit

The Maximum Securing load of the lashings must equal the 50% weight of the cargo unit

What is the purpose of the IGC code?

The purpose of the IGC code is to provide an standard for safe carriage of liquefied gases in bulk

The purpose of the IGC code is to protect the oil companies

The purpose of the IGC code is to provide an international standard for safe carriage of liquefied gases in bulk

The purpose of the IGC code is to provide safe carriage of liquefied gases in bulk

In the formula 0.9LBD (tonnes) for the amount of high density bulk cargo that can safely be loaded in a cargo hold, what is the value of ‘D’?

The summer load draught

The tropical load draught

Maximum depth of the cargo hold

Moulded depth of the cargo hold

During regular inspection of alternator windings it is found that windings are always covered with a heavy oil film coming from the atmosphere surrounding the auxiliary engine. After cleaning with an approved solvent, what should be done?

Reinsulate the windings after each cleaning

Take no additional action

Blank off intake air filters

Improve material of intake air filters

In describing oil cargoes, what is "sour crude"?

A crude oil from West Africa

A petroleum product which reacts with water during tank-washing, leading to a distinctive odour about the tank deck

A crude oil cargo which has left substantial residues in the bottom of the tank after discharge

A term used to describe crude oil or products containing appreciable amounts of hydrogen sulphide and / or mercaptans

For a cargo compartment on a chemical tanker to meet the definition and requirements of a "pressure tank", what must its design pressure be?

At least 1.0 bar gauge.

At least 2.1 bar gauge.

Less than 0.7 bar gauge.

Greater than 0.7 bar gauge.

What special requirements applies to fire alarm signalling systems in passenger ships

Same requirements for Fire alarm systems applies to all ships

Remote control of fire doors and reactivation of ventilation

Centralized in a continuously manned control station with remote control of fire doors, Indication of open or closed fire doors

Fail safe, Centralized in a continuously manned control station, Remote control of fire doors, Indication of open or closed fire doors, Reactivation of ventilation, Detector status, Back up powered

Which of the following is the purpose behind holding a pre-cargo transfer meeting before discharging a number of chemical grades?

To enable the master to confirm that ship's personnel have been advised of the cargo operation requirements on the Vessel Particular Questionnaire mailed to the ship's agent prior to arrival in port.

To ensure that all personnel involved are aware of the details of the proposed cargo operation, the services required and the safety considerations.

To establish tank readiness and the status of any other pre-operation preparations in order for the master to be able to confirm a time of arrival.

To ensure that the responsibility for all items on the Ship/Shore Safety Checklist is assigned and understood before the vessel arrives alongside.

During start up of a steam plant it is necessary to warm through the steam range prior to use. How should this warming through be carried out?

Open the bypass/warming through valve and then fully open the main stop valve over a period of two minutes to ensure the warming through is completed as quickly as possible.

Using the bypass/warming through line for the main stop valve and with all line drains open to ensure all condensate is removed.

With the line drains closed to avoid losing too much high quality water.

Crack open the main stop valve and keep the drains open.

All heat burns should be

Covered with Gauze or bandage immediately

Applied with soothing lotion as soon as possible

Treated by the doctor only

Cooled as quickly as possible with running cold water for at least 10 minutes

The lights displayed here indicate that this is one of two types of vessel. What are the two options?

A power-driven vessel engaged in towing, more than 50 metres in length, or less than 50 metres in length and showing a second masthead light, length of tow under 200 metres, seen head-on OR a power-driven vessel underway. Less than 50 metres in length and displaying the second all-round white masthead light, seen head-on.

A vessel engaged in fishing, restricted in her ability to manoeuvre, shooting nets OR a vessel engaged in towing, less than 50 metres in length, length of tow under 200 metres, towing vessel restricted in her ability to manoeuvre, seen head-on.

A power-driven vessel engaged in towing, less than 50 metres in length, length of tow under 200 metres, towing vessel and tow restricted in their ability to manoeuvre, seen head-on OR a power-driven vessel underway, more than 50 metres in length, or less than 50 metres in length and showing a second masthead light, restricted in her ability to manoeuvre, seen head-on.

A vessel engaged on pilotage duty, engaged in deploying or recovering a pilot, seen head-on or a power-driven vessel underway, lmore than 50 metres in length or less than 50 metres in length and showing the second masthead light, seen head-on.

Which is the most important factor in the safety awareness of the ships crew?

The safety awareness of the senior officers

The level of emergency-preparedness

The quality of emergency drills

The shipboard training provided

"From the list below, which is among the recommended actions for a vessel to take, on entering an area known for pirate activity?"

To transit with maximum safe speed

To transit at night time only

To turn off all lights

To confine all ship’s personnel to one room onboard

With reference to diesel engine ancillary system operation, which one of the given statements is true?

The normal jacket water temperature before the jacket water cooler is approximately 80 to 90 C.

The normal temperature of the lubricating oil before the lub oil cooler is approximately 80 to 90 C.

The normal scavenge air temperature after the charge air cooler is approximately 80 to 90 C.

The normal temperature of heavy fuel oil after the fuel oil heater is approximately 80 to 90 C.

What kind of safety protection is to be weared during a mooring operation?

Safety shoes and boiler suit.

No particular.

Gloves and helmet.

Helmet, safety shoes, gloves and protecting cloths.

What is a proportional band

Any part of the total amplification

100/amplification

Amplification/10

Amplification/100

The meaning of lapping a valve and valve seat is:

Machining the valve in a lathe machine.

Grind the valve against the valve seat to obtain a uniform sealing surface

Repair by welding

Adjust the overlapping of the inlet and exhaust valves

A road trailer is marked as follows: SWL 70t; Tare wt. 6t. What is the gross weight of the trailer when carrying it maximum payload?

76 tons

420 tons

70 tons

63 tons

What is the disadvantage of using High Tensile Steel (HTS) in the construction of bulk carriers?

HTS is prone to fatigue cracking

When compared with mild steel HTS increases the lightship displacement

HTS does not form a proper bond with paint coatings

HTS is prone to pitting

What is the typical size of a LNG carrier?

12,000 - 50,000

200,000 - 250,000

75,000 - 80,000

125,000 - 145,000 cbm.

On RoRo passenger ferries, the passengers are not normally allowed to be on the car-deck during sailing. What is the reason for this rule?

To prevent damage and burglary to the cars.

In case of an emergency situation, the car deck can be difficulty to find the way around, and cars can shift position caused by ships movement.

If the car deck are empty, it will be easier for the crew to locate all passengers in case of an emergency

The ships movement can make the cars slide/move and a person can be trapped between two cars.

Why is grain bundled?

To prevent it from wetting

To prevent bulk grain from shifting

To aid stability

To compact the cargo

What would be the most probable cause if the exhaust gas from a diesel engine looked a bit blue in colour?

Bad fuel oil.

Clogged charge air cooler.

Engine is too cold.

Engine burning too much lubricating oil.

If a vessel is fitted with “free flow system”, what does it mean?

That the cargo is free flowing in all tanks at all times.

A vessel without ordinary bottom lines where the cargo flows from tank to tank through bulkhead valves.

The vessel is not equipped with own discharging equipment.

That the vessel is only able to load on gravity.

Due to the relative low resistance of a Pt 100 sensor we might have to compensate for the cable-resistance to ensure a correct reading. Which of the 4 alternatives given is correct for the connection of this compensation resistance.

Figure 4.

Figure 1.

Figure 2.

Figure 3.

A 3-phase cage rotor induction motor requires protection by a time delay overload trip. What is the reason for this?

It will tolerate fault conditions during start up

Fuses act too quickly

Fuses act too slowly

It will allow for inrush current or motor specific faults

The thermal conductance capability is expressed by a material's thermal conductance number and states the heat quantity. What is the denomination for heat quantity?

Calorific value.

Enthalpy.

Joule.

Watts.

How many categories of Seed Cake are there in the Code of Safe Practice for Solid Bulk Cargoes (BC Code)?

How to prevent liquid from getting into the cargo compressor?

By checking the pressure in the vapour line between the cargo tank and the cargo compressor.

By using a liquid condenser on the vapour line between the cargo tank and the compressor.

By checking the temperature on the vapour line between the cargo tank and the cargo compressor.

By using a liquid receiver on the vapour line between the cargo tank and the cargo compressor.

What is likely to happen if a randomly hose is used for gas measurement?

The hose will most likely absorb hydrocarbon gases.

Nothing in particular.

The hose won't fit the indicator inlet ports.

The indicator will malfunction.

Passenger ships shall either carry automatically self-righting liferafts or canopied reversible liferafts. What does it mean that a liferaft is automatically self-righting?

The liferaft will automatically turn back into an upright position when it is fully loaded with people

One person can manage to turn the liferaft back into an upright position

It means the same as self-righting lifeboats

The liferaft will automatically turn back into an upright position when it is empty of people

Which international code are regulating what safety equipment a passenger ship must have onboard?

MARPOL

SOLAS

IMO

STCW

Данный онлайн-тест состоит из 90 случайных вопросов из тестов CES 5.1 по выбранной вами тематике.